110280 Kenmore Washer - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Slow water or no water fill, timer not advance.
3 of 4 people
found this instruction helpful.
-
Russell from AMARILLO, TX
- Very Easy
- 15 - 30 mins
-
Nutdriver
Took off back, popped off top, replace valve
Was this helpful?
Thank you for voting!
out of balance
2 of 2 people
found this instruction helpful.
-
Charles from ARVADA, CO
- Really Easy
- 15 - 30 mins
-
Nutdriver
The info. was really helpful
Was this helpful?
Thank you for voting!
On Spin cycle washer jumping all over the place.
2 of 2 people
found this instruction helpful.
-
Tuan from LADSON, SC
- Really Easy
- 15 - 30 mins
-
Socket set
Just follow the video! Very easy.
Was this helpful?
Thank you for voting!
Found seal had split on agitator cap
3 of 5 people
found this instruction helpful.
-
Kim from Cleveland, OH
- Really Easy
- Less than 15 mins
I clean out the fabric softner dispenser on my machine on a regular basis and found the seal split. After looking at several sites to try and find this part, I found this one. Ordering couldn't have been easier and repair only required pulling up the cup for the softner and installing the cap.
Thanks for making finding part ... Read more so easy . . . .
Thanks for making finding part ... Read more so easy . . . .
Read less
Was this helpful?
Thank you for voting!
Washer wasn’t spinning fast enough to get the water out and it had a slight burning electrical smell.
2 of 2 people
found this instruction helpful.
-
craig from Oxford, CT
- Really Easy
- 15 - 30 mins
-
Pliers, Socket set
I simply followed your clutch drive repair video on YouTube, that wasn’t the problem so I replaced the motor… remove the cover that goes over the drive belt by taking out the two screws, remove the belt, unplug the wire connector going to the motor and remove the two bolts that hold it up and it falls right into your hand. Then reverse
... Read more
the process and that’s it. Very easy repair.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
Loud banging during wash cycle
2 of 2 people
found this instruction helpful.
-
HARRY from BEND, OR
- Really Easy
- 15 - 30 mins
-
Screw drivers, Socket set
This is an easy one. Snap off the agitator cap with a screwdriver.
Remove the single but and agitator.
Remove 6 phillips head screws.
Lubricate the bearing and coax it off the spindle.
Remove the single but and agitator.
Remove 6 phillips head screws.
Lubricate the bearing and coax it off the spindle.
Was this helpful?
Thank you for voting!
Lid lock lite would not activate.
2 of 2 people
found this instruction helpful.
-
John from PUYALLUP, WA
- Very Easy
- Less than 15 mins
-
Screw drivers
The most difficult was to lift the top up. Releasing the clips was tough to push in and it broke some porcelain. The 3 screws on the plastic instrument cover was all that was required. Track the wires and remove the plug in and pull the wires through the access hole and misc clips, a Phillips screw driver removes the plastic switch .Simpl
... Read more
y place the new switch under the lid and the worst is done. Once the lid was up, 10 minutes and your done.
Read less
Was this helpful?
Thank you for voting!
Washer would not adgitate
2 of 2 people
found this instruction helpful.
-
Joe from SAN JOSE, CA
- Very Easy
- Less than 15 mins
-
Nutdriver
I ordered a lid switch because the washer wouldn't agitate. Most reviews indicated that was the problem. While waiting for the part to arrive, I discovered the transmission to be of fault.I let parts select know that I no longer needed the part. Parts Select gave me an immediate refund no questions asked and before I returned the part to
... Read more
them. That is customer service!! I will use Parts Select for all my future purchases. I can trust a company that trusts its customers.
Joe M. San Jose
Joe M. San Jose
Read less
Was this helpful?
Thank you for voting!
Belt needed to be replaced
2 of 2 people
found this instruction helpful.
-
Raymond from BRISTOL, CT
- Really Easy
- 30 - 60 mins
-
Socket set
Took the Cover off and installed belt.
Was this helpful?
Thank you for voting!
Washer would go into an unbalanced error code
2 of 2 people
found this instruction helpful.
-
Javier from SAUCIER, MS
- Easy
- 30 - 60 mins
Replaced 4 suspension rods. Had to release washer top from body case by twisting putty knife between lid and body. Once released swung lid up and propped against wall to access suspension rods. Replaced all rods and reinstalled lid. Good test run, no unbalanced error.
Was this helpful?
Thank you for voting!
My washer was always off balance.
2 of 2 people
found this instruction helpful.
-
Tracy from CONWAY, AR
- Really Easy
- 30 - 60 mins
-
Screw drivers
I used a jack to lift the tub and unhooked the rods and replaced them. Works great.
Was this helpful?
Thank you for voting!
violent basket wobble
3 of 5 people
found this instruction helpful.
-
Keith from DUNBARTON, NH
- Really Easy
- 15 - 30 mins
-
Screw drivers
remove basket and replace drive hub kit
Was this helpful?
Thank you for voting!
Water would not drain from tub.
2 of 2 people
found this instruction helpful.
-
Jerry from DUBOIS, WY
- Really Easy
- 30 - 60 mins
-
Nutdriver, Pliers
Used shop vac to remove as much water as possible. Turned washing machine on side to access pump. Removed old pump. Installed new pump. Used nutdriver to attach three fasteners and pliers to attach clamps to hoses.
Was this helpful?
Thank you for voting!
would not spin
2 of 2 people
found this instruction helpful.
-
John from INDIANAPOLIS, IN
- Really Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers, Socket set
online videos were great. called to order and lady was very helpful. washer is now operating normal
Was this helpful?
Thank you for voting!
Water would not drain.
2 of 2 people
found this instruction helpful.
-
Corey from RUSSELLVILLE, AR
- Really Easy
- 30 - 60 mins
-
Nutdriver, Pliers
Follow the video instructions.
No brainer..
No brainer..
Was this helpful?
Thank you for voting!