11027112601 Kenmore Washer - Overview

Enter a part description. DIY Heroes keep it simple, eg. "belt" or "pump".

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Washer Direct Drive Water Pump – Part Number: WP3363394
$60.45
In Stock
Washer Direct Drive Water Pump
★★★★★
★★★★★
(61)
Part #WP3363394
This pump is intended for use with washing machines that do not have belts. This drain pump has two ports for water to pass through: a large one, and a smaller one.
Suspension Spring – Part Number: WP63907
$16.15
In Stock
Suspension Spring
★★★★★
★★★★★
(4)
Part #WP63907
The suspension spring supports the outer tub and keeps the tub steady during loads that could cause an unbalance. If this part breaks, is worn down or has stretched out and lost its spring, it could cause the load to be off-balance which can lead to excessive shaking, moving, noise, and leaks. For this repair, you will need a 1/4 nut driver, a putty knife, a flat blade screwdriver, and a pair of needle-nose pliers. Disconnect the power supply, fill hoses, and drain hose to give you safe and easy access (have a container nearby for water left in drain hose). This item is sold individually, which is important as you may need to repair multiple springs in your appliance, which carries three suspension springs. As an inexpensive part, we recommend purchasing several at a time, as they can be very useful to have on-hand.
Lid Switch Assembly with Leads – Part Number: 3949247
$60.45
In Stock
Lid Switch Assembly with Leads
★★★★★
★★★★★
(60)
Part #3949247
This switch (Lid Switch Assembly With Leads, Washer Lid Switch, Lid Switch Assembly, Washer Lid Switch) tells the washing machine that the lid is closed, which allows the wash cycle to begin. The lid switch mounts to the underside of the cabinet top panel. The plastic on the actuator can become brittle with age and break when the lid is closed roughly. It can also break from the movement of an unbalanced load causing parts of the washer to strike it. This part must be replaced if it is broken and no longer being activated by closing the lid (indicated by the washer not agitating properly, or the machine not detecting the lid is closed). This switch is black plastic with wire leads. It is sold individually.
Washer Tub Spring – Part Number: WPW10250667
$12.95
In Stock
Washer Tub Spring
★★★★★
★★★★★
(23)
Part #WPW10250667
This part is used to balance the tub during spin cycle. Sold individually.
Touch-Up Paint - White – Part Number: 72017
No Longer Available
Touch-Up Paint - White
★★★★★
★★★★★
(23)
Part #72017
This 18 ml bottle of white appliance touch-up paint is used to cover scratches or marks on your appliance. The white touch-up paint can be used on refrigerators, microwaves, ranges, clothes dryers, and freezers. This is a genuine OEM part and includes a brush applicator. Please remember to wear gloves to protect your hands when applying this paint.
Agitator Bolt – Part Number: WP358237
$15.56
In Stock
Agitator Bolt
★★★★★
★★★★★
(5)
Part #WP358237
This kit contains one screw with rubber gasket and threaded sealant. The screw head is 7/16".
Washer Drain Hose – Part Number: WPW10358149
$49.45
In Stock
Washer Drain Hose
★★★★★
★★★★★
(22)
Part #WPW10358149
It connects from the pump to the back panel. The clamp is not included.
Tub Wear Pads - Package of 3 – Part Number: 285744
$21.54
In Stock
Tub Wear Pads - Package of 3
★★★★★
★★★★★
(14)
Part #285744
This package of pads contains three tub wear pads.
Centerpost Gasket – Part Number: W10814296
$12.01
In Stock
Centerpost Gasket
★★★★★
★★★★★
(6)
Part #W10814296
This main outer tub seal is a critical component that prevents water from leaking at the bottom of the tub during operation. Measuring approximately 2 inches in diameter, it is constructed from durable black plastic for long-lasting performance. Proper installation requires disconnecting power, drain hose, and inlet hose, followed by removing the outer cabinet and the entire tub assembly. Inspect the seal for cracks or wear during maintenance to avoid leaks and ensure optimal washer performance.
Washer Front Leveling Foot – Part Number: WPW10001130
$9.85
In Stock
Leveling Spring – Part Number: 8316845
$15.00
In Stock
Leveling Spring
★★★★★
★★★★★
(2)
Part #8316845
This spring is used on the leveling components in a washer. Please note, this spring may differ in appearance, but functions the same as original.
Washer Washer – Part Number: WP3949550
$17.26
In Stock
Washer Washer
★★★★★
★★★★★
(1)
Part #WP3949550
This part goes on the agitator retaining bolt.

Common Symptoms of the 11027112601

How this model fails, and the parts that fix it.

Watch our pros, then fix it yourself.

See how others fixed this model. Time, tools, difficulty, and steps that lead to victory! View More

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Washer stopped mid cycle
1025 of 1051 people found this instruction helpful.
  • Travis from Pearland, TX
  • Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers
1. Unplug washer.
2. Remove screws at control panel end caps.
3. Flip control panel back to expose wiring.
4. Detach lid switch wiring harness from control panel.
5. Use screwdriver to pry the 2 brass clips holding the back panel of the washer to the front and sides piece.
6. Tilt the front/sides piece over to exp ose lid switch.
7. Use nutdriver to detach ground wire.
8. Use screwdriver to remove 2 screws holding lid switch in place.
9. Install new lid switch. Make sure wiring harness piece is facing the right direction.
10. Put washer back together in same order it was disassembled. Make sure front/sides piece connects to the clips at the bottom.
Was this helpful?
Thank you for voting!
Water pump leaking when machine used.
594 of 637 people found this instruction helpful.
  • Tom from Granby, MA
  • Really Easy
  • Less than 15 mins
  • Pliers
The hardest part of this job was pulling the machine away from the wall so the hoses could be disconnected and the machine flipped onto it's back. Putting the machine on it's back does two things. It drains the water left in the bottom of the tub so it won't pour out onto the motor when the old pump is removed, and gives the necessary a ccess to the pump. Once the machine is on it's back you remove the hose clamps with a pair of pliers and disconnect the hoses. The pump is secured to the motor with a pair of spring steel retaining clips which are easily popped off by hand. Once the clips are removed, the pump is in your hand. Put the new pump in place, replace the retaining clips and hoses, and you're done. This has to have been the easiest repair I've ever done. I wish cleaning gutters was this easy.
Was this helpful?
Thank you for voting!
The lid switch had broken on my washing machine; the machine would not run.
576 of 602 people found this instruction helpful.
  • Dennis from Evans City, PA
  • Easy
  • 15 - 30 mins
  • Screw drivers, Socket set
First I unplugged the washing machine. Then I removed the two screws that hold the top console in place; these are located in back of the main console (where the dials are). Once removed, the entire console swivels back, exposing the wires underneath. I unplugged the wiring harness that was connected to the washing machine top flat sur face. I then removed the two s-shaped brackets with a screwdriver by prying underneath. This allowed me to remove the main sheet metal frame around the washing machine. The lid switch assembly is located under the top console. I simply removed it and replaced with the new assembly and put it back together. A snap!
Was this helpful?
Thank you for voting!