Models > 11026071690

11026071690 Kenmore Washer - Overview

Sections of the 11026071690

[Viewing 10 of 10]
Keep searches simple, eg. "belt" or "pump".
Agitator Directional Cogs – Part Number: 80040
Agitator Directional Cogs
★★★★★
★★★★★
(119)
PartSelect #: PS388034
Manufacturer #: 80040
These agitator directional cogs are commonly referred to as dog ears. They come four to a package and are usually used with direct drive washing machines.
$5.21
  In Stock
Direct Drive Motor Coupling – Part Number: 285753A
Direct Drive Motor Coupling
★★★★★
★★★★★
(57)
PartSelect #: PS1485646
Manufacturer #: 285753A
This coupling kit is located between the motor and the transmission on direct drive washers with no belt. This is the newer version and is made with new metal sleeves for added strength.
$32.60
  In Stock
Direct Drive Water Pump – Part Number: WP3363394
Direct Drive Water Pump
★★★★★
★★★★★
(46)
PartSelect #: PS11741239
Manufacturer #: WP3363394
This pump is intended for use with washing machines that do not have belts. This drain pump has two ports for water to pass through: a large one, and a smaller one.
$67.73
  In Stock
Suspension Spring – Part Number: WP63907
Suspension Spring
★★★★★
★★★★★
(4)
PartSelect #: PS11743345
Manufacturer #: WP63907
The suspension spring supports the outer tub and keeps the tub steady during loads that could cause an unbalance. If this part breaks, is worn down or has stretched out and lost its spring, it could c...
$6.74
  In Stock
Clutch Assembly – Part Number: 285785
Clutch Assembly
★★★★★
★★★★★
(35)
PartSelect #: PS334641
Manufacturer #: 285785
A worn clutch can cause a slower spin speed which will leave your clothes wet after a cycle. This clutch assembly comes with brake cam driver, blue spring for large capacity washers and black spring f...
$58.46
  In Stock
Water Inlet Valve with Mounting Bracket – Part Number: 285805
Water Inlet Valve with Mounting Bracket
★★★★★
★★★★★
(23)
PartSelect #: PS334646
Manufacturer #: 285805
The valve body of this part could be blue or green in color. There are two ports for water to enter, and this valve is compatible with a half inch ID hose. It has two 3/4-11x1/2 NHT hose threads.
$46.73
  In Stock
Tub Spring – Part Number: WPW10250667
Tub Spring
★★★★★
★★★★★
(15)
PartSelect #: PS11751118
Manufacturer #: WPW10250667
This part is used to balance the tub during spin cycle. Sold individually.
$9.02
  In Stock
Agitator Bolt – Part Number: WP358237
Agitator Bolt
★★★★★
★★★★★
(5)
PartSelect #: PS11741866
Manufacturer #: WP358237
This kit contains one screw with rubber gasket and threaded sealant. The screw head is 7/16".
$9.02
  In Stock
Thrust Spacer – Part Number: 285587
Thrust Spacer
★★★★★
★★★★★
(1)
PartSelect #: PS334562
Manufacturer #: 285587
This white thrust spacer is made of plastic and is also commonly referred to as a retainer ring. It is used in the agitator assembly of many direct drive washing machine models. This is the retaining ...
$6.27
  In Stock
Tub Wear Pads - Package of 3 – Part Number: 285744
Tub Wear Pads - Package of 3
★★★★★
★★★★★
(6)
PartSelect #: PS334620
Manufacturer #: 285744
This package of pads contains three tub wear pads.
$18.69
  In Stock
Agitator Repair Kit – Part Number: 285748
Agitator Repair Kit
★★★★★
★★★★★
(13)
PartSelect #: PS334622
Manufacturer #: 285748
This agitator repair kit comes with a long cam, a thrust spacer and four dogs ears (agitator cogs). This repair kit is used to move the upper agitator and it connects the base of the agitator with th...
$43.29
  In Stock
Foot, Front - Single – Part Number: WPW10001130
Foot, Front - Single
★★★★★
★★★★★
(1)
PartSelect #: PS11747965
Manufacturer #: WPW10001130
Sold Individually.
$9.02
  In Stock

Questions And Answers for 11026071690

We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.

Common Symptoms of the 11026071690

[Viewing 22 of 22]
Will not agitate
Fixed by
these parts
Show All
Leaking
Fixed by
these parts
Show All
Pumps but will not spin
Fixed by
these parts
Show All
Shakes and moves
Fixed by
these parts
Show All
Noisy
Fixed by
these parts
Show All
Spins slowly
Fixed by
these parts
Show All
Will not drain
Fixed by
these parts
Show All
Will not stop filling with water
Fixed by
these parts
Show All
No hot or cold water
Fixed by
these parts
Show All
Will not fill with water
Fixed by
these parts
Show All
Burning smell
Fixed by
these parts
Show All
Will Not Start
Fixed by
these parts
Show All
Timer will not advance
Fixed by
these parts
Show All
Leaks water
Fixed by
these parts
Show All
Fills and drains at the same time
Fixed by
these parts
Show All
Marks left on clothes
Fixed by
these parts
Show All
Will not tumble
Fixed by
these parts
Show All
Does not dispense fabric softener or detergent
Fixed by
these parts
Show All
Not cleaning dishes properly
Fixed by
these parts
Show All
Touchpad does not respond
Fixed by
these parts
Show All
Lid or door will not open
Fixed by
these parts
Show All
Lid or door won’t close
Fixed by
these parts
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
No movement from Basket & agitator
The job looked intimidating but turned out to be very easy.
First take off the water pump by removing the two clips that hold it in place. Place a shallow pan under the pump to catch the water that is in the pump and hoses. Open the hose clamps with a pair of pliers or channel locks (better) and slide the hoses off of the water pump.
The motor comes off next. Unplug the electrical connector from the motor and two wires from the capacitor. Remove the two screws holding the clamps in place and then pop off the two clamps. You will need to hold up the motor with one hand while you remove the clamps or it will fall to the floor once the clamps are removed.
One piece of the coupling assemble will be attached to the motor and the other will be attached to the gearcase drive shaft. If you want to clean up the mess created by the shredded rubber center piece of the coupling assembly you will have to take off the motor mounting plate. It is held on by two bolts and removing it makes installing the coupling easier but probably not necessary.
Push the back half of the coupling on to the gearcase drive shaft until the shaft is flush with the face of the coupling. Install the new rubber center piece on to the coupling then re-install the motor mounting plate. Install the other half of the coupling on to the motor shaft and lift the motor up to the coupling. You have to rotate the motor shaft by spinning the fan blades until the coupling lines up so you can slide it into the other half of the coupling. Then just reattach the motor, connectors and water pump in the reverse order of disassembly.
Parts Used:
Direct Drive Motor Coupling
  • Jeff from Wayne, NJ
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Pliers, Screw drivers, Socket set
1045 of 1109 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
washer wouldn't agitate
First pry off the cap of the agitator. Then using a socket remove the bolt that holds the plastic cup in place. Remove this cup by prying it loose from the two tabs that hold it in place. Once this cup is removed you can get to the broken cogs.
Slip the new cogs into the underside of the cup, and slide the cup back down in the agitator housing using the slots on the side for a guide. (You may want to remove the entire agitator and assemble everything upside down, then flip it all back over to mount, so the cogs don't fall out).
Tighten the bolt, snap the cap back in place on top of the agitator and your'e done. Easy repair.
Parts Used:
Agitator Directional Cogs
  • mike from Kent, WA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers, Socket set
888 of 948 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Washer not agitating
On top of the agitator is a flat cap that is held in place by the friction of an o-ring, there are no fasteners. I would imagine one could get under the lip with a small screwdriver or butter knife to pop it off but I chose simply using my fingernails so as to not disfigure the cap. Under the cap you will find the head of the only bolt that holds the assembly together it is a 7/16 head and because it is in a 4" deep well your will need a 6" extension for your ratchet. Once the bolt is out the top of the agitator, the assembly with the cogs removes by hand. Set the assembly upside down on the counter, slide the black plastic ring off, pull the cogs out with your fingertips, install the new cogs put a new black ring on and set the assembly back in the agitator. Reinstall bolt. As the bolt is down in a tube, you cannot set it in place with your fingers and it will fall out of the socket. To hold the bolt in the socket during positioning you can either put a gob of Vaseline on the bolt head to hold it in the socket or form a small piece of paper over the bolt head and set it into the socket, the friction of the paper will hold the bolt into the socket. Took me less then 10 minutes, good luck
Parts Used:
Agitator Directional Cogs Agitator Cam Bearing Thrust Spacer
  • Craig from Polk City, FL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Socket set
627 of 657 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!