11021492311 Kenmore Washer - Overview

Enter a part description. DIY Heroes keep it simple, eg. "belt" or "pump".

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Drive Hub Kit – Part Number: W10528947
$39.32
In Stock
Drive Hub Kit
★★★★★
★★★★★
(38)
Part #W10528947
This drive hub kit helps your washer spin and agitate properly by connecting the basket to the motor. If your washer isn’t spinning, is noisy, or wobbles too much, this part might be the fix. It’s a simple DIY repair with easy-to-follow instructions and usually includes everything you need to get your washer working again.
Washer Washer – Part Number: WP3949550
$17.26
In Stock
Washer Washer
★★★★★
★★★★★
(1)
Part #WP3949550
This part goes on the agitator retaining bolt.
Screw, 8-16 x 1.000 – Part Number: WP8533953
$9.85
In Stock
Screw, 8-16 x 1.000
Part #WP8533953
Sold individually.
Washer Sealtub – Part Number: W10324647
$90.28
In Stock
Washplate Bolt – Part Number: W10772621
$11.61
In Stock
Washplate Bolt
Part #W10772621
Sold individually.
DRIVE BLOCK RETAINER – Part Number: W11385424
$16.95
In Stock
DRIVE BLOCK RETAINER
Part #W11385424
Dryer Screw – Part Number: WPW10109200
$11.66
In Stock
Dryer Screw
Part #WPW10109200
11-16 x 3/4 Sold individually.
Washer Suspension Rod Kit – Part Number: W10780044
$164.09
In Stock
Washer Suspension Rod Kit
Part #W10780044
The suspension rod kit supports the washtub and keeps it stable during unbalanced loads.
Surface Element – Part Number: W11168414
$108.28
In Stock
Surface Element
Part #W11168414
Cook with confidence using this 6-inch coil element. It heats evenly at 1250 watts and installs easily with pigtail connections. A simple way to restore your cooktop’s performance—just turn off power before replacing.
Lint Filter – Part Number: WPW10215093
$78.75
In Stock
Lint Filter
Part #WPW10215093
Ring Tub – Part Number: WPW10556325
$152.41
On Order
Ring Tub
Part #WPW10556325
We're here to help you get your washing machine back to peak performance with the Whirlpool Upper Outer Tub Ring. This isn't just a simple part ? it's an authentic Original Equipment Manufacturer (OEM) part. The difference? Higher quality and greater durability, meaning fewer worries for you. Now, why do you need this Upper Outer Tub Ring? It acts as your washing machine's champion, serving as a splash shield. It fits right over the top of your washer tub, helping keep water where it belongs, ensuring each wash is as efficient and effective as possible. Compatibility? We've got you covered. This Ring works seamlessly with select models from well-known brands like Whirlpool, KitchenAid, Maytag, Jenn-Air, Amana, Inglis, and Magic Chef, making your repair job that much simpler. Installation of this Tub Ring? It's a breeze. Although don't forget to wear your work gloves for safety. Before you snap it into place, just make sure it matches your current part to ensure the perfect fit and function. Count on the Whirlpool Upper Outer Tub Ring to get your washing machine back to working like new. Don't settle for anything less when it comes to your appliance repair needs.
Screw – Part Number: WP8533928
$10.43
In Stock

Common Symptoms of the 11021492311

How this model fails, and the parts that fix it.

Watch our pros, then fix it yourself.

See how others fixed this model. Time, tools, difficulty, and steps that lead to victory! View More

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Hub had warn its grooved teeth off and washer wouldnt agitate
66 of 93 people found this instruction helpful.
  • Allison from RICHFORD, NY
  • Easy
  • 15 - 30 mins
  • Screw drivers
ordered hub and it shipped quickly. I was able to put the hub in place and screw the screws in. you want to tighten them down slowly and go around to each screw tightening a little at a time so you don't break the hub. as you tighten the screws down the hub slides down flush. its impossible to just push the hub on with your hand. Buttoned it back up and got caught up on laundry. good day when the washer is fixed.
Was this helpful?
Thank you for voting!
Waher would not spin and made noise
25 of 29 people found this instruction helpful.
  • Andrew from SYLVANIA, OH
  • Very Easy
  • Less than 15 mins
  • Screw drivers, Wrench (Adjustable)
Removed center cap, loosened center nut, pry lightly up on center plate and tap center nut. Center plate comes loose, remove nut, remove center plate. Pry lock clip out and remove, remove screw with electric impact (screw drive will work, but slower), remove drive hub. Install new drive hub (be sure to check screw hole alignment), install and tighten screws (be sure to follow a skip pattern and bring it down even), install lock clip, install center plate, install and tighten nut, replace center cap. Done!
Was this helpful?
Thank you for voting!
washer not agitating
22 of 23 people found this instruction helpful.
  • David from EAST AMHERST, NY
  • Easy
  • 15 - 30 mins
  • Socket set
This was a learning experience but it appears to have worked out in the end. Our 3 1/2 year old washer was not agitating much and I attributed that to a loose bolt. I would tighten the bolt and it would work ok for a load or two and then stop agitating. I would find that the bolt was loose again. I took a number of steps to try to get the bolt to stay on tight - threadlock, a new bolt, more threadlock, and applying progressively more force on the bolt, with no better results. Yet the repair guys on you tube were saying the bolt only needs to be snug, not super tight - something was amiss. I even went so far as to secure the basket with a rope so I could use two hands on the socket wrench (please don't do this). But when I tried the washer again there was no agitation at all! I observed the agitation output in manual test mode and the bolt was turning in lock step with the shaft but the agitator wasn't turning at all. That's when I suspected that the problem was actually a worn lower agitator. Trouble was that now I couldn't seem to get the bolt off. Turning the wrench caused the shaft itself to rotate so I couldn't loosen the bolt from the shaft. I thought I broke the washer. Then I considered that maybe the shaft was rotating because the washer was in an agitation mode when I turned it off. I went back into manual test mode, made the washer spin, then turned it off. Fortunately, this worked. The shaft was again stationary and, albeit with great difficulty, I got the bolt off.

I removed the agitator, and as a pro would have figured out long before, the ridges inside the top of the lower agitator were almost completely worn down. I realized then that the contact between these ridges and the splines on the shaft is what is supposed to cause the lower agitator to move with the shaft. The purpose of the bolt is just to keep the agitator in the correct position and from coming off the shaft. I had been trying to compensate for the worn agitator ridges by over-tightening the bolt, creating some contact at the top of the shaft. This would work for a little while, then the agitator would start slipping, and the slipping agitator was acting just like a wrench loosening the bolt (until my stupid rope trick, that is.)

So I ordered a new agitator (only the lower agitator was bad, but the price of an entire agitator isn't a lot more than just the lower part and I was reading that the upper agitator parts will wear over time) and another new bolt (because my repeated attempts to over-tighten the first one I ordered had split the rubber gasket apart and worn the bolt head).

The new agitator fit snugly on the splines of the shaft so I sensed no need to use excessive force on the bolt. Just an easy one-handed snug tightening with the socket wrench, using the other hand to hold the lower agitator. The washer is now working again.
Was this helpful?
Thank you for voting!