11016982500 Kenmore Washer - Instructions

leaned washer back on wall at or more than 45degree undid two screws off of motor. pulled old part off put new on reinstalled motor Done

I ordered the new cogs but didn't want to wait the few days for them to arrive. So I decided to try and temporarily repair the old ones. After looking at the picture of the new ones on this site I realized that the teeth were just worn down. I took all four of them out and used a grinding disc to carve the teeth down deeper. They were not perfect. (I would recommend holding the teeth with a vise.) However, after reinstalling the cogs the machine worked perfect and that was two weeks ago. I'm not going to install the new ones until I have to.

Being female & never working on appliances, it was a challenge for me. I took the spinning unit apart: 1) Outer cap 2) Inner cap 3) Screw, nut & bolt popped out. Rusty & wouldn't lock into place anymore. Ordered nut & washer at about $10 + shipping. Total $17 from MayTag Rec'd right at 7 days via USPS. Used nutdriver/wrench to screw in new bolt w/washer. Wah la! That did it! Washer working great now! Now that I'm a "diy" handy person, I'm ready for my next challenge. Hopefully, none!

Watch the video

Tipped the washer onto it's side, used pliers to loosen clamps on old hose. Removed outer drain hose from white plastic hose adapter on back of washer. Removed white hose adapter (snaps out of place) and old hose. Fed new hose through opening for white adapter, then snapped new adapter into place on back of machine. Put the new hose in place and replaced clamps. Sat washer back upright. No more leaking! It was easy and didn't take more than 15-20 minutes.

We unscrewed the two screws at the back of the control panel. Holding the control panel on both ends
we pulled it toward the front of the machine, slightly and gently lifting it at the same time, removing it from the metal surround. Holding the control panel up off of the surround we rocked the surround forward and lifted it off the washing machine frame.
We could see where the leak was coming from. We took the hose clamps from the two ports, then
using a pair of pliers pulled the two clips that are holding the pump onto the shaft protruding from the
electric motor. We matched up the part on the web sight. Ordered the part then when it came in we just reversed the order putting the machine back together. The hardest and most time consuming
thing about this repair was the clean up of the washing machine. (Dirt and soap residue does
build up on the inside of the wash tubs.)

Unplug power cord. Turn off hot and cold water to washer. Disconnect water lines at the back of the washer, but mark which is hot and cold on the hoses . Remove drain hose from the sink tub or sewer line but keep it elevated so the water don't run out. Tip over on the backside but put something under the back side like a tool box to keep the top elevated a little bit, but not on the control panel just below it. Now remove the two screws that are in the motor retainer. Now pry motor retainers loose then lift out motor and remove old coupling. Now install new coupling. If it is a little tight on the shaft, use a deep socket a little bigger than the shaft to tap them on. Line up coupling while putting motor in place. Then snap on motor retainers. Look at the coupler make sure it is straight and not s shape. If it is s shape, remove and tap coupler on shaft a little more. If it is straight then reinstall the two screws you removed in the beginning from the motor retainers. Hook up drain line, water lines hot to hot, cold to cold. Then check for leaks on water lines. Plug in ,turn on, if it sounds ok. Don"t stand there, wash something.

snapped off the 2 springs on the water pump,took off hoses with pliers,took off the 2 little screws on the motor springs.snapped off the 2 springs on the motor,and the motor came off.took out the drive coupling,it just slides off...then reverse the procedure,and you are done...

Thank you for asking me how it went. the washer would not spin or pump water out, so I put it on its side and saw that the coupling was bad.
so I found you on the internet, thankyou very much, and put a order in for the part. well waiting for the part, I took the old coupling out it was easy, there was two metal bands one on each side of the motor took them off two bolts holding a plate on, and had old coupling in hand. and it was easy to put back with the new coupling. I enjoyed working on it. Dennis

First I removed the cover but not the back. Then I removed the water pump by useing a flat head screwdriver to remove the clips. I did not have to disconect the water hoses. Then I used a driver to remove the motor clips and pulled the motor off. You need to put something under the motor to support it until you remove the screws holding the brackets. The coupling came off with ease. I replaced it with the new one using a spark plug socket to tap it onto the motor. I did the same thing to the other half that attatched to the gear assembly. It will be easier to put the black rubber center on the gear assembly then line it up with the motor by turning the blades. Then I put everything back in reverse order. Very easy job.

Make sure you UNPLUG your washer first. It is also a good idea to remove the water intake hoses from the back to avoid damage to them or the valves.

Getting the outer panels off was the hardest part for me. There are 2 screws on the back of the function panel. You don't have to remove the screws completely, just until they are unscrewed from the bottom base. Then I gently pulled forward and up on the function panel and it flips back exposing the wiring. There is one wire harness plug that needs to be disconnected toward the center of the panel.
There are 2 large metal clips that are removed by pressing a flat head screwdriver into them. Press down and slightly toward the front of the washer and it will release the clip. Be careful, mine popped up and flew behind the washer.
Once the clips are removed you can pull the entire caging of the washer (top, front, right and left side panels as one) away from the machine. This will expose the entire innards of the washer.
In the front at the bottom is the water pump. It is very easily removed. Pinch the clamps around the hoses with a pair of pliers and move them up the hoses. Pull both hoses off the pump.
There are 2 metal clamps holding the pump in place. You can release them using a flat head screwdriver as well. Once free from clamps, the pump can be pulled straight forward to be removed.
Replace the pump with the new one, placing it in the same place and position as the old one. Attach the clamps back on. Mine were really hard to reattach as the tension was really tight.
Then slide the hoses back on and use the pliers to squeeze and slide the clamps back down the hoses to secure them to the pump.
Replace the cage of the machine. On my particular model, the front panel hooks under a metal lip and the side panels rest on them, so it was a challenge getting it back into place by myself in the small area I was working in.
Replace the metal clips on the top using the flat head screwdriver by pulling slightly toward the front of the washer and pressing down.
It was a little scary, I thought I was going to pinch myself.
Then reattach the one wire harness, flip the console back down and secure tightly.
Screw the 2 screws back in on the back of the function panel and your done. Reattach the hoses and plug in your washer.

This was my first washer repair. I did it with some sketchy online instructions for a different model washer. It took forever to get the washer open and was even more frustrating to put it back together. Changing out the pump was simple once I got in there. I saved over $100 in labor by doing this myself and in only took about 45 minutes.
I think I'm ready to open up the dryer and give it a good cleaning.

First. I unplugged the washing machine from the electrical source. Then, I unscrewed the two screws in the front and the two screws on the back holding the control panel onto the washer. I lifted the control panel off and let it hang in the back of the washing machine. I unplugged the white plug connecting the control panel from the machine. I used a screw driver to pry the two giant spring like clamps and the cabinet released from the actual washing machine. At the bottom, I found the pump, unclamped the small clamps holding the pump on, pulled it off, installed the new one ( I used pliers to get the hose clamps where they needed to be) and then reversed by steps. Easy as pie and saved me a bunch of money

Removing top console control panel, deataching 2 clips and removiong the entire box to get access to the agitator and the direct drive, one part on the top and other on the bottom of the washer,removing top cap of the spinner got access to the agitator. Using 1/2" socked and pliers remove & rep[lace the agitator. for the direct coupling: remove the water pump (2 clips) 1/4" socked & screw driver remove the electrical Motor, remove & replace the direct coupling, put all removed parts back toguether, reasembly the box ataching clips on place, console panel Install, perform operational check, was good I have the washer running like a new machine.

Turn off the power,remove the washer cabinet top and side panels. unsnap the water pump clips, unscrew and unclip the motor mounting clips.Remove the old drive coupling and triangular drive shaft adaptors.Clean area and install the three new parts, reattach the motor and pump, close the cabinet,turn the power back on and test.Done! The only hard part is working down on the floor and you need a good flashlight.

Unplug washer. Place large old towel in floor at rear of washer. Turn off and disconnect water supply lines and allow to drip dry. Place towel in floor in front of washer. Tip washer forward onto face of washer. Unplug wiring clip connector from drive motor. Remove 2 1/4 inch head screws from spring clips on bottom of motor housing. Slowly rotate clips out of the was to drop motor. Knoch top coupling piece off agitator shaft with screwdriver and light hammer. replace coupling with 5/8 deep well socket as a driver which will fit the metal insert in the coupling and not interfere with the shaft. then drive the other coupling onto the motor shaft using light hammer and drive socket(5/8) deep well. place the rubber shock connector onto the agitator drive piece then slide the motor back into the mount position. rotate the clips vback into place. tighten 1/4 head screws in clips re-attach the wiring harness tip the washer back up onto "feet" re-attach water supply lines tighten appropriately. Plug unit into receptacle and enjoy....