108RB545-G General Electric Range - Instructions

Repair was simple (just lift off the old and put on the new). What was pleasantly surprising was how quickly I received the parts (amazing)!

Lastly, I've been looking for the correct parts/sizes in stores for years (yes, I should have tried this sooner). I was delighted to finally find a place that actually had the correct parts.

First I turned the circuit breaker switch off for the stove unit. I then removed the two screws that hold the element in place at the back of the oven. I then pulled the element out about 3 inches and disconnected the two wires. I attached the new element, bolting the wires into place and then screwed the element back into place on the back wall of the oven. I flipped the breaker switch back on, and turned on the oven. I was done in roughly 15 minutes. The most difficult part was having to shine a flash light into the oven to replace the part, and negotiating the hard cold kitchen floor.

Received the Drip bowls and Rings very quickly. Opened the box and then cut open the plastic wrap that the individual rings and drip bowls were in. Lifted the burner on the stove top, took out the old ring and drip bowl. Installed the shiny new drip bowl and ring, then lowered the stove top element back into place. I was able to replace all 4 of them within 5 minutes. Made the 30 year old stove look brand new.Thank you for perfect fit parts and fast delivery.

I first removed the two screws holding the element in place. Then I pulled the element out about 2 or 3 inches and then took out the 2 small screws holding the 2 wires in place. I then removed the old element and discarded it and installed the new one in the reverse order that I took out the old one. It was quite easy to do, only took about 10 to 15 minutes total time.

So this ancient stove we inherited when we bought our house had the drip bowls wrapped in tin foil. We've searched EVERY (not joking) store in our area for drip bowls that would fit it, but apparently Hotpoint wanted to make sure you could never do this - well, at least not easily. No one, not one store carries drip bowls to fit it. I finally searched online and partselect.com came up first on the list. I was amazed they had the right part! Better yet, ordering was beyond easy, and they came super quick. Popped in the parts in less than 2 minutes, and we're good to go - makes this old stove look new! (well, if this was the 80's, lol) When I clicked on the part it said which stoves it would fit, which was also very helpful. Thank goodness for Part Select! Otherwise we would've had to rewrap those disgusting old bowls... I'd recommend this site in a heartbeat!

Replaced all the ordered parts, and straightened a bent "rest piece" (one of three) on the element os the large burner, which made it rest perfectly on the new Trim Ring. It doesn't easily fall down into the bowl now while I am using the burner. The new Bowls look so nice, and the stove looks nearly new!

I now know where to go for help when I need to repair appliances. You seem to have everything that could possibly be needed. Thank you!

Simply took the replacement part ( PS244040, GE WB30X341) and did the quick direct swap using all the new pieces in the burner kit. UNPLUG the stove. Undo the titl arm screw, remove the plastic wire isolation block (2 spring clips), unscrew the 3 wires to the elements, screw the 3 wires to the new element, put in new bakelite wire isolation block with spring clips to keep the wires seperated, mount and titghten the tilt arm screw. Make sure the burner sits even and flat in the stove top. Plug the stove back in and test.

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires...)

Replace part an wires

I just replaced them.

Lifted burner element to remove pressure on ring and drip bowl. Removed old parts and replaced in reverse order. This not intended to sound sexist, but my wife who is not particularily mechanically inclined performed the task on her own.

the replacement items fit really good. It was a matter of remove and replace,

Just lifted the electric components Remove drip plans and trim rings and replaced with new drip pans and trim. Your company was incredible in there delivery of the parts..One day. You made my husbands very happy.

lift eye slide in bowl and trim ring, put the eye back down,

Customer service is great. Fast shipping. Great communication. I have them bookmarked from a previous order. Same good service as the first time. Thank you.