1067640641 Kenmore Refrigerator - Instructions

I removed 7 screws hold the heavy cardboard cover on the rear of the fridge. The dificult part was taking the screws that hold the 3 fan motor braces on the fan out. After that it was a matter of making the wire conections and putting it back in. I did not have enough room to laydown to do the work, If i had it would have been a lot easier to see the screws that had to be removed. All in all an easy job, and the part was a perfect fit.

Unplug fridge, unpluged fan motor from plug socket, removed bracket screws, removed fan retainer clip from shaft. removed screws holding fan to bracket

I just popped out the old switch with a flat head screwdriver. Removed the connections and then installed new switch by reversing steps. Popped in back in and the light went on.

Removed cover change mounting bracket on fan put it back in works great

Followed video and had one problen, the metal pipe would not release as shown,so I used a hacksaw between the plastic and metal pipe, removing the metal pipe from inside as the video shows. Good instructions.

Very easy. Left the front of the refrigerator so it is approx. 4 inches of the floor. (used a two by four. Removed the screws (one for each roller). Removed the rollers and replaced with new rollers. Reinstalled the screws with secures the rollers to the refrigerator. Done

Watched instructional video, read all printed instructions and repair related posts
It's all there. Works great! Thank you!

Pried out old part with screwdriver. Unplugged. When new part came, just plugged it in and pushed the part into place.

I removed one bolt and took out the old roller after first blocking up the fridge. Then I was puzzled for a moment because the hole in the new assembly was not tapped. But then I saw that the old bolt was a self tapping bolt. I used it to tap the hole then removed it and installed the new assembly. No sweat job.

Removed old one and installed new one.

I pulled the socket out and unplugged the wires. I replaced the light socket by plugging in the wires and snapping the light socket into place. A very simple fix.

removed old and instaslled new. biggest problem was getting to one of the screws.

Unplug, turn off water supply, carefully remove lower back cardboard cover, unscrew old valve mount, lay towel down, disconnect the three water lines, modify provided “L” bracket by drilling a hole outboard of one of the slots to match/fit the wider original mount holes on the refrigerator’s bottom pan, screw top/short end of bracket to valve, cut back the two clear lines about 1/2” for a “fresh” end, connect all three lines, position valve and secure with original screws (access is tight, used small 1/4” wrench), turn on water/check for leaks, install back lower cardboard, plug in and verify function.

For a year the filler tube would freeze up and stop all water flow. I would remove it and use a heat gun on it. I decided that the fill valve was leaking after 20y and actually saw drops coming out of the tube when the valve was off. So I watched the videos and ordered the parts. So far no freezing up and working as originally. The valve kit came with all the parts I needed to replace and reconnect the plastic and copper tubing connections. Very pleased with the outcome after a week as well as the videos and complests parts needed. The fill tube didn’t need shorthing and was used as it came. Adding, easy to replace and connect to the water supply line. My refrigerator location made the repair a little difficult ( small kitchen) but with patience it all went well. Not as difficult if access to the back side is easier. Not the fault of the parts supplied! Also to mention, I vacuumed out 20 years of dust from the coils while I had the back off. Same for the front side. A must do often to extend the life and air circulation.

removed lower back cover. diconnected fan ass'y electrical connection, removed fan housing (3 screws). removed fan motor from housing. cut old connector from fan and installed on new fan with wire nuts included. re-installed new fan to housing and re-installed housing to frame.