10651759713 Kenmore Refrigerator - Instructions

Remove 4 self tap screws holding on front cover/bin handle. Remove 2 self tap screws holding drum cover. Remove 1 self tap screw at back of bin holding door actuating rod and spring, slide forward to disengage. Remove "E" clip and flat washer. Remove plastic nut {clockwise/left hand threads]and remove crusher parts [keep in order removed]. Slide new drum on shaft and reassemble crusher in reverse order. Install drum cover w/2 self tap screws. Install flat washer and "E" clip. Re install actuator rod and spring assy. Install front cover and test in refrigerator. The 2 self tap screws that hold drum cover are easier to remove with a 1/4' drive ratchet and 1/4" socket because of limited space behind actuator rod. This job is a snap to do. I'm sure it's at least $50.00 cheaper than a service call.

Unplug Dryer. Remove 2 5/16in hex screws from lower panel and remove panel.Remove 3 5/16in hex screws attaching lint duct. Remove 8 1/4in hex screws attaching blower housing. Remove 2 1/4 hex screws attaching thermostat to blower housing. Using adj. wrench on back of motor shaft nut to hold, loosen fan assy. w/ 7/8in socket. Remove 3 5/16in hex screws holding fan housing to motor mount. Remove 2 5/16in hex screws holding housing and motor mount to base floor. Push belt pulley wheel up enough to loosen belt and take off rear motor pulley. Motor w/mount can be slid out bottom for replacement [wires are layed toward front].Using 6in flat tip screw driver press down to unlock front & back motor bushing holddown clamps. Pinch electrical wire connector ends to pull off old motor. Remove and Install new motor, reversing steps. Belt replacement [suggested w/new motor] requires removal of 2 5/16in screws to lift/remove door w/front panel [disconnect door switch wires upper right rear corner].Remove 4 5/16 screws holding front bulkhead. Once bulkhead is pulled up and off, allow front end of drum to sag and rest IN PLACE [removal not required to slip old belt off and install new belt]. Note belt location point around drum. Slide new belt on. Reinstall bulkhead and panel/door [Don't forget door swich wires]. Adjust belt into position and push spring-held belt pully up to allow looping of new belt around rear motor belt pulley. Complete w/hand turning of drum to ensure belt is aligned and feeding properly. Reinstall lower fan housing/covers/thermostat,etc removed for motor installation.

At first I went to a local part supplier and they didn't have it in stock but could order it for me for $55.00 plus $10.00 to ship it. I told them I would have to think about it. I went home and got on the computer and found your web site and was I shocked when I saw the same part listed for $6.98 and $7.00 to ship it. You guys saved me $50.00. The part arrived in two day and took 5 min. to install. I now have light in my refrigerator. Thank you.

I removed the ice bucket and dumped the ice (saving part of it to put back into the bucket after repair).Using the nut driver,removed all screws,rmoved the auger that the broken drum is mounted on.I reoved the nut on the end of the auger(with my pliers).Slid out auger removed broken drum,replaced new drum and re assembled using your easy to follow instructinns.

Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you

Not so easy as others have described. I kept the parts off the auger together in my hand as I replaced the drum. Thanks to the people who mentioned the nut being left handed. Taking a picture before dis-asembly saved me. I would never have gotten it back together otherwise.

Once I removed the ice bin from the freezer section of refrigerator and removed all the necessary screws was able to remove the auger drum, but had some difficulty in reinstalling the crusher blades in the dispenser. After several tries, got it right and dispenser is performing like new.

removed six screws removing the cover and exposing the shaft & auger.

I then had to remove the snap ring & undid the end nut that has left handed threads.removed the 6 auger plates and then replaced all parts in reverse order of their removal.

Removed screws, Ice maker blads, and broken Auger Drum. Reverced order and replaced with new Auger Drum.

The manufacture needs to change the part from a plastic Auger Drum to a metal aluminum Auger Drum. This is the second one I had to change in 4 years.

I removed the 4 screws holding the front cover in place. Removed the 4 screws holding the ice auger cover in place. Removed the c clip holding the auger on the shaft. Pulled out the auger shaft. Removed the broken auger drum and replaced with the new one. Reassembled in reverse order.

Took the Ice Bin Out emptyed it then removed the nesasary screws pulled the broken Peice off and sliped
the new part on held the metal peices together so we would know how to keep them in order for fear of putting them in wrong place but we did it now it works great thank you so much for getting the part to me so quickly your great.

remove the ice container. and i got to work

Pulled out the ice tray, took whatever screws held the front on. The rest was pretty easy. The only thing I would say was a problem was taking off the cutters. The front spacer is threaded, and loosens by turning clockwise. Also, the shaft that runs along the side of the tray has a spring and keeper. Make sure yoiu remember how you take it apart.

removed 9 screws, removed all parts, laying them in order, so they would be easy to replace.
reassembled in order I had removed them placing the new auger drum in place of broken one.
replaced ice container in freezer, poured in a few ice cubes them crushed them.

looked at the schematics from online