10651143110 Kenmore Refrigerator - Instructions

Great service. Unpluged old switch and pluged in new one. Works great

I pried the old one out with a screw driver and pushed the new one in. I expected instructions in the box it came in but there were none.

I installed a Ice Door Kit. It works Great Now!

I spent several hours defrosting the unit. Making sure the vents were all defrosted and free of ice. The part replacement is fairly straight forward; remove the thermostat, cut two wires, reconnect the wires following color codes, attach to coil and restart. And, "Yippie!". Nothing. Zilch. Zero. Because I could not connect with the online repairman, I spent 40 bucks for nothing; problem was not resolved. Thanks for taking my money. I'm bummed and with just a little less money in my pocket. Never again will I ever purchase another Whirlpool product. Or buy from your outfit again (because of the over priced part). I replaced a 25 year old 'working' General Electric fridge for this junk that sat in the warehouse for four years before this was delivered to me in 2018 and sold to me as a "new" appliance. This was found out only when it crapped out and I needed to have it checked out for repair. Oh yea, I only had the comment section and the part recommendation to go by, and the latest comments are at least two years old. I'll be surprised if this even gets posted.

My owners manual said to unplug fridge from elec outlet, use a kitchen knife to gently pry off the switch plate
(manual had a pictoral example), unclip the two wire, replace with on new switch and replace the switch. Close
door and plug back in. Open door to check that the lite
works. Walla! It did. Thanks!

Sincerely, Ron Marshall, Billings, MT

My ice maker would not produce ice. I removed motor module which involved removing ice maker from freezer, removing motor module cover and 3 screws. I found short (burnt place) in copper of existing module. Ordered new motor module, replaced, and all is fine. Great service, quick delivery and correct part.

Popped the old one out with a kitchen knife and popped the new one back in. It tool less than 15 seconds!!

shook bottle and painted waited a day and repeated

Used the instructions on your site.

Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you

Please bear in mind I am 65 years old & it was harder to get up & down off the floor then to change the switch. Was very easy - watched video, unplugged unit. I used the putty knife at the right front corner to work loose, when it came loose had to loose the left side a little. The unit pulled out easily. detached the wired that had a single plug with 2 prongs on it. Attached the plug, pushed new switch into place. There was no way you could place wires on wrong prong. When done, plugged refrigerator back in & checked if working. I CAN SEE THE LIGHT and the food in the freezer now. Thank you for making an easy repair.

unplug freg.took everything out.pulled out shelves and pulled out back panel.their was my part i had to replace.

Turn off power to the frig. Remove the shelves and back brackets from the freezer, then with a 1/4" nut driver remove the nuts holding the rear metal panel in place. Once removed the defrost thermostat is right in front of you. You will have to clip the wires from the old t-stat because they are in a harness. Once clipped, strip the wires back, wire in the new t-stat, add wire nuts and put it all back together. Very easy job to do, works great. Thanks Parts Select, Mike.

unplug refrigerator, take backing off with nut driver. Pull old blade off and put new blade on. Put backing back on and plug in.

followed the video as instructed. Saved two repairman calls, one to find the problem, one to install. Net savings was about $130.00