10650212010 Kenmore Refrigerator - Instructions

Mine is a simple tale of the missing ice cube dispensor guide. When we moved, the guide was missing so when I built our new home with a kitchen in the basement I wanted to hook up the ice dispensor but when I did, the ice cubes always fell off to one side. I decided to order the misssing part on-line. I ordered it paid for it and then received it the next day-wonderful. Within ten minutes, I was ready to go. Thanks for great service. Rick Davis, Bloomington, IL.

Be advised that to do this job, you have to take the ice tray and feeder assembly completely apart. The only tricky part is that the nut, part 31 in the drawing, that holds everything together is reverse threaded. Since it's plastic, you're afraid you'll break it. If you know it's reverse threaded to begin with you can go ahead and apply the required force to get it off.

Turn off water supply too ice maker and unplug the fridge power. using a nut driver remove one bottom screw from the bottom, near the front. The other two from the side atop the ice mold. (loosen screws and ice maker will lift up and off.)
I set the ice maker on the counter, snapped of the front cover by hand. using a phillips driver, remove two screws near the bottom corners.(they go through the circuit board into the ice mold)
circuit board in one hand, other end of ice mold in the other, slowly pull apart about 1 inch. remove the silver colored "on, off" bar at the end by snapping the retainer out of the ice mold. (the silver bar stays with the circuit board end)
Watch how the ice guide(white fingers stationary on side of ice mold) hooks too the ice mold on each end. swap ice guide to new ice mold, insert three guide pins on end into holes on the circuit board, while holding ice guide onto ice mold, watch rotation bar while inserting into motor.(it only splines one way.) when each piece is lined up, simply push together and reinstall two screws. snap circuit board cover into place. reinstall ice maker into freezer in reverse order.

After removing a few screws to get to the drum my husband had it back to working like a charm.This part seems to be better made than the original part in the refrigerator.

Unplugged the starter from compresser and put the new part in and all worked. Great service and I like the OEM parts not aftermarket. Will definately do service with you again. Thanks for making my life easier.

Removed the three motor screws pulled off old motor put new motor in place replaced screws and re-installed. It was producing ice three hours later. I originally tried to obtian these parts directly from Whirlpool in which twice they shipped me the wrong parts. Finally gave up on them and entered the whilrpool part number which crossreferenced to new part number which was correct the first try. Thank you!

I removed 4 screws holding the motor mounting bracket and removed the assy from the unit. I then removed 3 screws holding the motor to the bracket. I put the fan blade on the new motor and reattached the motor to the bracket. I plugged in the wiring adapter to the motor and reinstalled the bracket in the unit with the 4 screws. Finally I attached the unit wiring connector to the motor.
It was relatively easy.

Removed 2 control panel knobs and face plate that is snaped in place using a knife to prey it causing to snape lose.
Removed 4 cover screws that gave me acess to Defrost Timer. Remove two fastining screws on timer unit. Remove electrical color coded 4 prong connector plug. Have to make sure black jumper wire on the new timer kit is connected to the correct one of the 4 prongs as to instruction sheet for my model refrigerator. Reassemble in reverse order. Bingo! Fixed.

I took the cover off the control settings and found the timer. Removed two screws and replaced the defective one with the new one. Had to pay attention to directions since the timer is used in different ways and to make sure the loose wire was installed correctly (not the same way as the original ground was connected).

Watched the website repair & adjustment video, ordered the part which was exactly like the one currently in the fridge. Took only 10 min. to install. Then, 2 hours later we had ice! And still have ice on a consitent basis. Easy fix, life's good!

First I unplugged the unit, then I popped off the cover to the icemaker electronics. Removed 4 screws, pulled out the broken electronic panel, and replaced with the new one. Returned the screws and cover. The next moring the ice bin was full.

This must have saved me $300, and the inconvernience of waiting around for the repair man. He would have made two trips since he would never have had this part with him.

removed 3 screws and power wire clip, removed old ice maker, reinstalled new ice make by snaping in power wire clip and the 3 screws that hold ice maker, reinstalled wire bracket/arm that stops ice maker once tray is full of ice. done

Removed catch tray and then removed two screws that are underneath. I left the control panel hanging from its wires, then removed the two screws from the control bracket.
A word of caution before next step: You need to remove the two micro switches on the left and right. While trying to remove one, it split apart and the pieces fell out. I was able to put it back together and it worked fine. So be careful with the micro switches.
Continue tranferring wires and switches to the new bracket and reassemble in the opposite order.
An easy repair.

Replaced the entire unit (fan and motor). Would have rated this repair as "Really Easy", but found it a little difficult because of large hands.

I first had to identify the faulty part. I ohms checked the micro switch in the door. It was fine. I traced the wiring to the inlet valve at the bottom of the rear of the unit. I checked the voltage to the solenoids and it was good. After checking the schematics on the Whirlpool website, I determined the only possible faulty part was the inlet valve. I found the correct part here on PartSelect and ordered it. When the part arrived I changed out inlet valves by turning off the water supply, unplugging the refrigerator, removing the two inlet valve mounting screws, and disconnecting the wire terminals. The inlet water line was a 1/2" compression nut and the water and ice outlets were hand turn compression nuts. I reversed the removal steps to install the new valve, turned the water on, checked for leaks, plugged in the refrigerator, and the new valve worked perfectly. The feeling of accomplishing a DIY project was only topped by a happy wife who really didn't want to spend the money on a new fridge!