10648212500 Kenmore Refrigerator - Instructions

My tenants moved out of my rental property and abandoned their refrigerator there. The freezer door would not close properly because someone had previously removed the lower door support bracket and failed to replace the lower bracket shim that positions the lower part of the freezer door properly out from the refrigerator cabinet causing the door gasket seal to bind before the freezer door was fully closed. I removed and replaced this lower door bracket with a new shim made up of serveral thicknesses of cardboard to achieve this spacing and freezer door now closes and seals properly. They had never connected a water supply to the refrigerator although this model is equiped with an ice maker and in door ice and cold water dispenser. The access panel on the back of the unit had been previously removed and discarded. I made up a new access panel from cardboard and connected the water line to the solenoid valve. Valve was so old it would barely open when valve energized and water flow was too slow to make proper sized ice cubes and fill a water glass. I purchased a new water solenoid valve and replaced ther original valve and cured that problem. Replacing the access panel cured an improper cooling problem because with panel removed, most of the air flow bypasses the condenser coils. Lastly I replaced the upper tubular light bulb and the lower light socket I purchased here and installed a 40 watt bulb in the new light socket. Presto! I was able to turn non working abandoned refrigerator into a workable unit.

First defrosted it to makes sure all Air flow was opened. Tested the Defroster heater with omh meter, it was OK. Found the location of the defrost timer on the online diagrams. Used nut driver to remove cover.
Replaced timer. The hardest part was decieding how to wire it up, tis was a universal kit and depending on how it was wired as to how often the defrost ran. The firt choice was every 8 hours. Since this was going to be opened often, I picked that one.
Plugged it with in 24 hrs freezer wall mesured -5 and the fridge was at 30, so had to warm it up a bit.
Now all complaints gone, Ice making has been doing better also.

remove old crisper pan
install new crisper pan
dispose of old crisper pan

Emptied door of food jars etc. Used socked on top plate. Removed door and placed on a flat surface. Used socket to take out cam on the bottom of the door. Replaced worn cam. Replaced nylon sleeve on the top of the refrigerator door with needle nose pliers. Placed door in the bootom slot with the new cam in place. Placed top plate in the new nylon sleeve on the door. Replaced screws with socket wrench.

the piece fit perfectly and delivery was within a couple days. very satisfied.

The repair video was a great help in this specific repair and matched my refrigerator model exactly. The only issue was an apparent design change in the thermostat that I received. The location of the electrical leads has changed. It might be worth mentioning this in the video. Polarity is not an issue in this case, but if it was, it would be worth noting in the video. So far the refrigerator has been operating normally.

Searched my issue on the internet then chose part select to see if bi-metal thermostat was available and it was so I ordered part which was under $30.00 incl. shipping. I then went to You Tube to watch how to replace the part but most importantly to find out where it was located and degree of difficulty. Replacement was rather simple and it fixed our 22 year old fridge. I must add that when I looked up the part it also told you what percent of the time that particular item actually fixed the problem based on others experience. I thought that was neat info. as I felt better about ordering something that may or may not fix my problem. Thank you,

Removed the 2 screws holding the light bulb shield, then the 4 uolding the metal panel. Unplugged the olw door switch and replaced.
reassembled the pieces.

My fridge was not cooling properly as I would have to tap the thermostat at times to get it to kick on again. Ordered the temperature control thermostat from this site t and watched video on how to install. Not hard at all and did it in under an hour. Fridge is working like new..

Removed old thermostat and replaced with new one. The video link in the shipping email was great - really detailed even though it was a simple fix.

I followed the procedures that others described that had the same problem,very handy

Removed old switch and installed new - but did not solve problem

Simple remove the fan and motor, plug in the new cord and screw in the new motor.

I recieved the replacement part the next day after ordering it. If you are some what mechanicaly talented this repair is very simple. The only tool that is needed is a nut driver. You may want to remove the bracket holding the water solenoid vavlves. Then you can pull them out of your way to remove the 3 screws holding the fan to the bracket. Once you remove the old fan motor just reverce your steps with the new motor. Check that all your screws are tight. Check to make sure that there are no wires in the way of the fan. Don't forget to attach the wire harness and re-attach the solenoid bracket. Ahh nice and quiet like new!

pulled fridge out, remove back cover, remove 4 screws holding fan put new fan in with new screws way easy dont call a repair man for this shipping was fast thank you for that