10644109300 Kenmore Refrigerator - Instructions

I guessed that the water dispenser solenoid was getting weak.
A quick web search led me to PartSelect's website where it was so easy to pull up my refrigerator model with diagrams. I ordered the valve kit, and in 5 days it was in my hands.

Installation was literally 10 minutes. It took longer than that to vacuum all the dust from under and in back of my refrigerator !

After taking apart the ice maker, the only obvious replacement was the motor assembly. I check various Internet sites and found the best price at PartSelect.

I removed the ice maker from the freezer after turning off the ice make switch. Removal was easy with only one screw holding in the entire assembly. The ice maker has rails that allow it to slide in and out like a drawer.

After R/R the motor assembly and returning the ice make to the freezer all that remiand was to see if it worked.

Within 10 minutes I had the wonderful sound of water filling the ice maker tray. Within 30 minutes of that, ICE!!!

Shopping, ordering and shipping of the part was fast and efficient. I'll go with PartSelect for all my future appliance needs.

Detached the broken ice guide by expandong the opening bewteen the tabs with my hands. Installed the new ice guide and pressed into place. Took about 3 minutes.

Replaced the cap no tools needed

I replaced this same ice maker a month before, if that long, using a part I found $40 cheaper from another site. Needless to say you get what you pay for, the existing part was not exactly the same as the original and leaked water all over the place. I removed the not so old icemaker by removing the flapper door and removing the harness cover then pulling out the existing icemaker followed by disconnecting the wiring harness. Now with the old icemaker removed I removed the bottom tray/shield from the existing ice maker by removing the three screws from it then attached the tray to the bottom of the new ice maker from PartSelect which did not come with the bottom tray/shield. Finally, I executed the removal process in reverse order to install the new ice maker.

I followed the instructions of other people on this website. First, removing the plastic guard that covered the wires leading to the diffuser. Then I removed the screw that held in the diffuser. I should have done this next part first--it would have ben easier! Anyway, next I removed the plastic cover at the back-top of the freezer. It looks like it guides air into the freezer. After that, there is another plastic air guide, that connects into the diffuser. I had to pull this out. There was no screw. I did use a flat head to wedge in, and pop it out. Then I just popped out the old diffuser and disconnected the wires. To install the new diffuser I just reversed all these directions. I took about 30 minutes. If I had had more experience with this sort of thing, I could have done it in 10. My fridge is now perfect! I used a thermometer to test.

First the small screws you sent did not fit.I had to cut and mend the old ones (2) to use them.I did purchase a connecting valve tha I used to connect the part of tubing (my name for it) from old one to new one.I was surprides it is working fine.Not bad for a nurse!

Determined that compressor was not running, after researching problem on another site they recommended i try the condenser moor fan or motor, the defrost thermostat or defrost timer. . I was not satisfied with their recommendations. If I had tried their recommendations i would have likely gotten frustrated and spent upwards of $3000 to replace the 22 year-old hand me down unit. Thank you Parts Select for properly diagnosing my relay failure saving me a ton of money.

directions very well written, easy to follow, no problems

Unplug power to refridg/freezer. Removed the screw in rt. rear bottom of ice maker to remove. After removing slightly, unplug pigtail. Remove ice maker completely. Remove large square cover from left side to expose motor. Remove screws to remove motor. Replce with new. Replace ice maker to freezer, plug pigtail back in, put screw back in rt rear bottom, plug refridg/freezer back into power source. Ice was making in about 2 1/2 hours.

Removed ice maker from fridge. Removed motor assembly (3) screws on cover, and (2) screws inside. Removed mold (3 screws on bottom) and replaced everything in reverse order. Note: Turned ice maker off for several days while waiting for parts. The water line on this particular model will freeze inside the freezer if ice isn't made for several hours/days. You will have to defrost to begin making ice again.

With instructions from PartSelect.com this was an easy fix. I tested the motor's electric as suggested and was satisfied that the Motor Module (WPL W10190935) would correct the problem. UNPLUG THE REFRIGERATOR! I popped the outside plastic cover off to expose the unit. (1) remove the wire unit that runs the length of the cube maker (2) remove the 3 screws that secure the motor unit and carefully remove it (3) carefully line up the new unit, slide in place and replace the 3 screws (4) install the wire that was removed in step(1). Connect electric to the refrigerator and wait about 2 hours for your first ice cubes. PartSelect.com is the ONLY supplier that you will ever need! Great instructions and trouble shooting suggestions. Shipping is incredibly fasssst! Customer contact is awesome. Don't hesitate to buy from them! Saved me about $200.! Good luck....Tom in SC

Removed Ice container; Removed two screws from housing around shaft; Pulled old shaft from freezer door; inserted new shaft in freezer door; replaced housing around shaft; replaced and tightened two screws securing housing; returned ice container. Tested by activating ice dispenser. It worked like new.

I removed two small bolts that secure the flapper that keeps ice from falling out when you open the door, one bolt that holds a cosmetic cover for the wires and slid the icemanker forward. The only difficult part was removing the plug since it was high up, the wires were stiff and there's a release to push that locks the two plugs together. Once it was removed all was installed in the opposire order.
The part I ordered had a slightly taller channel where the water refills so I had to trim it to allow the new icemaker to slide in without bending the fill nozzle. Other than that it was pretty easy.

Very easy to order from parts select. Took seconds to replace.