092902-2085-99 Briggs and Stratton Engine - Overview
Sections of the 092902-2085-99
[Viewing 5 of 5]
Keep searches simple, eg. "belt" or "pump".
Cap-oil Fill
PartSelect #: PS8945667
Manufacturer #: 281658S
This manufacturer approved replacement part is specially produced for use with Briggs and Stratton engines commonly installed on Toro lawn and garden equipment. It is utilized to keep the oil in the t...
$7.95
Special Order
Spring-vert Rew Str
PartSelect #: PS8965473
Manufacturer #: 390066
Spring-Vert Rew Str
$36.95
Special Order
Seal-oil
PartSelect #: PS8966301
Manufacturer #: 391483S
This is an authentic replacement part manufactured for use with small engines. This oil seal keeps oil inside the crankcase, and seals the shaft. It is recommended to replace the crankcase gasket when...
$10.95
Special Order
Kit-pump/choke Dia
PartSelect #: PS8966318
Manufacturer #: 391681
This genuine manufacturer approved replacement part is designed for use with lawn and garden equipment. Fits 3.5 and 4 gross HP vertical crankshaft engines (pulsa-jet carburetors). This item provides ...
$38.95
Special Order
Muffler
PartSelect #: PS8967008
Manufacturer #: 394569S
This is an authentic exhaust muffler specially designed for Briggs and Stratton engines commonly used on Toro lawn and garden equipment. It is supplied directly from original equipment manufacturer an...
$19.95
Special Order
Seal-o Ring
PartSelect #: PS8936675
Manufacturer #: 270344S
This authentic OEM replacement part fits a variety of Toro and Briggs & Stratton engines. An O ring is used to retain pressure between rigid parts. Its flexible material allows it to create a tight se...
$5.95
In Stock
Order within the next 4 mins and your part ships today!
Common Symptoms of the 092902-2085-99
[Viewing 1 of 1]
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Could not keep an aftermarket muffler on the engine.
Once I determined what OEM muffler I needed, installation was relatively easy. I have a 1982 4hp Briggs on my Snapper tiller. There was a 90* galvanized elbow coming out of the exhaust port, with a bezel nut to lock it down. Do not remove the elbow, even though it appears that you should. If you install the muffler without the elbow the muffler will parallel the the vacuum for the carburetor and can melt the rubber couplers. Use the elbow to direct the heat away from the carburetor. Use a pipe wrench to lock down the bezel nut because the weight of the muffler, especially under vibration, can work loose and fall down on the tine belt cover and melt it. The bezel nut that comes with the muffler should also be used to lock down the muffler to the threaded intake bracket that comes with the muffler, not to replace the bezel nut for the elbow.
Parts Used:
-
Richard from KERNERSVILLE, NC
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Wrench set
15 of 20 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Muffler rusted out
-
Snoopy from TYRONE, GA
-
Difficulty Level:Very Easy
-
Total Repair Time:30 - 60 mins
7 of 18 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Push mower leaked under neath.
Pulled the old seal out, replaced it with seal #391483S and so far looking good !
Parts Used:
-
Raymond from Coalport, PA
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Pliers, Socket set
1 person
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!