Whirlpool Dishwasher Dishracks | Replacement Parts & Accessories | PartSelect

Popular Whirlpool Dishwasher Dishracks

Dishwasher Upper Rack Adjuster – Part Number: WPW10546503
Your Price
CAD$41.41
Dishwasher Upper Rack Adjuster
PartSelect Number PS11756150
Manufacturer Part Number WPW10546503
This OEM Dishwasher Upper Rack Adjuster is a grayish-black, plastic part which will require a screwdriver to install. It fits onto dishwasher rack and connects it to the track allowing it to slide in and out. If broken then the rack will no longer slide properly, and the part must be replaced. The installation has been rated as "easy" by customers. Before beginning any repair, you should unplug the dishwasher and wear gloves to protect your hands. Check your model number and user manual to see if this part is right for you! Your dishwasher should have a left and right upper rack adjuster, and both are the same part. These parts are sold individually, so if you are looking to replace both, you will need to order two parts. Please see as follows for detailed repair instructions: Release the track stops from the upper dishrack rails and pull the upper rack from the dishwasher and place it upside down on a work surface. Raise the wheels to the maximum height. Release the top of the long rear clip from the dishrack tine and push the clip down to the release point and remove it. Press the tab down on the front clip move the clip up to pull it off. Release the locking tabs on the clip in the middle of the height adjuster and remove the clip. Using a slot screwdriver pry the housing cover down and out to release the upper tabs on each side. Pry the bottom of the housing cover out of the 2 lower locking tabs. Pull the housing cover off the rack. Remove the adjuster housing and wheel assembly and repeat the procedure on the other side. Slide the vertical portion on the new wheel assembly between the fourth set of vertical tines from the back of the dishrack and rotate the wheel assembly so that it lays flat against the side. Insert a positioner clip above the rear wheel and snap the tab into the slot. Install a positioner clip on the front wheel. Position the adjuster body over the vertical portion of the wheel assembly and push in into the slots. Locking tabs at the bottom of the adjuster body engage the wheel assembly once it is fully inserted the tabs. Insert the actuator lever into the adjuster body with the thumb pad facing the front of the rack. Two half-circle cutouts on the adjuster body hold the actuator in place. Push the adjuster body down and install the adjuster cover. Install the adjuster cover mounting screws. Repeat this process on the other side of the rack. Push the upper dishrack onto its tracks.
Fixes these symptoms
Door latch failure
Door won’t close
Leaking

See more...
Dishwasher Rack Adjuster Kit - White Wheels – Part Number: W10712395
Your Price
CAD$61.44
Dishwasher Rack Adjuster Kit - White Wheels
PartSelect Number PS10065979
Manufacturer Part Number W10712395
This authentic Dishwasher Upper Rack Adjuster Kit with white wheels is a kit made up of primarily plastic and metal components, and which will require a screwdriver to install. This kit comes with all the necessary parts for a dishwasher rack adjuster. It fits onto dishwasher rack and connects it to the track allowing it to slide in and out. If broken then the rack will no longer slide properly, and the part must be replaced. In many cases, our customers have reported the top rack of their dishwasher hanging down or sagging due to the adjuster kit, particularly the wheels, have broken or failed. If you are having problems in this area, this kit will help get your dishwasher back up and running. Check your model number and user manual to see if this part is right for you. The parts for this kit come as a package and are not generally sold individually. Please see as follows for detailed repair instructions: First you will have to remove your upper dish rack and the old adjust kit. Now, when installing the new kit, count 4 rungs from the back of the basket toward the front. Take your new metal adjuster and thread the shaft through the fourth rung. You may have to tilt it to get it through. When you straighten the part the portion of the wheel should be on the outside of the rack and the shaft will be on the inside of the rack. Take your positioner clips and use them to secure the adjuster to the rack. You will see two front tabs and two back tabs. The back tabs will also need to be tilted into place so that they are on the inside of the rack. The flat part of the positioner clips should be on the outside of the rack. Then you will push the clips down on to the adjuster to clip them into place. Now you will have to install the adjuster body on to the adjuster. Pull your adjuster all the way down. Tilt the adjusted toward the inside of the rack, you will notice that the adjuster body has a channel that will fit the adjuster. Slide those two pieces into place together. You will have 4 notches on your adjuster body that fit perfectly with your rack. Pull on your metal adjuster to lock it into place. Grab your actuator. You want to make sure that the thumb pad of your actuator is facing toward the inside of the rack and is closer to the front of the rack. Pull the adjuster arm up as far as you can, so that the body is a little bit above the top of the rack. The set the actuator inside of the two slots at the top of the body. You may have to tilt the body toward the inside of the rack to fit the actuator into place. Once you have that part in place, push the whole assembly down and press it back up against the side of the rack into place again. Now you will take the adjuster cover and install it on to the body from the outside of the rack. There is a little tab at the top of the cover, you will have to push that into place in the slot at the top of the adjuster body. That just snaps down into place. Then you install your two T15 Torx screws into the cover to hold it into place. This installation is the same for both sides.
Fixes these symptoms
Door latch failure
Door won’t close
Not cleaning dishes properly

See more...
Rack Stop Clip – Part Number: WPW10195622
Your Price
CAD$6.13
Rack Stop Clip
PartSelect Number PS11750071
Manufacturer Part Number WPW10195622
This manufacturer-approved Rack Stop Clip is a gray plastic part which can be installed with a screwdriver. Measuring slightly over an inch in length, it prevents the rack from sliding too far and falling off. If broken or damaged, then the rack will slide too far and this is a sign the part should be replaced. It attaches to the end of the top dishwasher rack. This clip can be used for the left or right side, and is sold individually. It is a good idea to replace both sides at once. To make this repair, start by pulling out the rack, then, using your screwdriver, reach in behind the rack stops and press the clips in. You should be able to remove the stops from the track from here. Next, you should be able to slide the track back over the rollers and snap the new track stop into place.
Fixes these symptoms
Door latch failure
Door won’t close
Not cleaning dishes properly

See more...
Rack Track Stop – Part Number: WP8565925
Your Price
CAD$11.75
Rack Track Stop
PartSelect Number PS11746591
Manufacturer Part Number WP8565925
The rack track stop on your dishwasher is designed to stop the dish rack at the appropriate place when opening and closing the rack. If your dishwasher is not cleaning your dishes properly, the rack stop may need to be replaced. The replacement part may differ slightly from the broken part, depending on the model. However, the different styles are interchangeable. This product is sold individually and comes in both a white and grey plastic version. Many of our customers found this repair to be very easy and takes less than 30 minutes to complete. Simply snap the old part out and snap the new part into place. You will not require any tools to complete the job. This is an authentic part approved by the manufacturer.
Fixes these symptoms
Door latch failure
Door won’t close
Not cleaning dishes properly

See more...
Tine Pivot – Part Number: WPW10082853
Your Price
CAD$11.75
Tine Pivot
PartSelect Number PS11748190
Manufacturer Part Number WPW10082853
The tine pivot clip, also known as the tine row pivot, is used in dishwashers and is located in the upper dishrack. At around 3 inches in length, the clip is used to keep the tine row in place in the dishrack. If your clip is cracked or damaged, it is best to replace this part. To repair, first lift the release tab and hold the other side to prevent it from falling off. After lifting it off, you can set the new clip on the tine row and lock it up. Refer to the manual provided by the manufacturer for further installation instructions and guidance. Remember to wear work gloves as a safety precaution. This repair was rated as very easy by our customers and should be done in 15 minutes or less.
Fixes these symptoms
Not cleaning dishes properly


Front Track Stop – Part Number: WPW10508950
Your Price
CAD$7.34
Front Track Stop
PartSelect Number PS11755805
Manufacturer Part Number WPW10508950
This stopper is attached to the front of the top dishrack track. This stop keeps the upper rack from pulling out too far and falling from the track.
Fixes these symptoms
No Symptoms for this part
Dishwasher Dish Rack Slide Track - Left Side – Part Number: W11259785
Your Price
CAD$63.95
Dishwasher Dish Rack Slide Track - Left Side
PartSelect Number PS12584376
Manufacturer Part Number W11259785
Fixes these symptoms
Door won’t close


Dishwasher Dish Rack Slide Track - Right Side – Part Number: W11259786
Your Price
CAD$67.51
Dishwasher Dish Rack Slide Track - Right Side
PartSelect Number PS12584377
Manufacturer Part Number W11259786
Fixes these symptoms
Door won’t close


Rail Stop Clip – Part Number: WPW10082861
Your Price
CAD$6.13
Rail Stop Clip
PartSelect Number PS11748191
Manufacturer Part Number WPW10082861
This part goes at the end of the rail to stop the dishrack from falling out.
Fixes these symptoms
No Symptoms for this part
Dishwasher Positioner – Part Number: WPW10195840
Your Price
CAD$43.28
Dishwasher Positioner
PartSelect Number PS11750093
Manufacturer Part Number WPW10195840
Also known as rack adjuster. Sold individually. This is an original part from KitchenAid, Kenmore, Whirlpool, Jenn-Air, and Maytag for use with Dishwashers. The dishrack adjuster arm positioner clip holds the adjuster arm in the right position on the dishrack. The most common reason for replacing the strap is if the rack will not stay in its desired position. This part is sold individually. There are no tools needed to replace the positioner.
Fixes these symptoms
Door won’t close