Get in touch, we're here to help!
1-866-883-8386
Monday to Saturday
8am - 8pm EST
CABLE HARNESS 00628468
Fits your SHX68T52UC!
$20.08
Special Order
Fits your SHX68T52UC!
PartSelect Number
PS8729251
Manufacturer Part Number
00628468
Manufactured by
Bosch
Troubleshooting
This part works with the following products:
Dishwasher.
This part works with the following products:
Bosch.
Part# 00628468 replaces these:
AP5691124, 628468
Customer Repair Stories
Average Repair Rating: 3.8 / 5.0, 1 reviews.
What's this?
- < Prev
- 1
- Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
Dishwasher Panel - not illuminating, no power
Dishwasher panel unresponsive when pressed. Check electricity and power was going to unit. Dishwasher had successfully performed last washing cycle (no mechanical issues) so focused on Operating Module that is located at top of door panel (concealed when door is closed), This is an easy repair if you take your time and gently remove the components. First, unplug the unit or shut power off at the circuit. Open the door fully, and place a pad or blanket under the door as you will be removing the front dishwasher panel (this unit is stainless steel).
There are phillips head screws around the perimeter of the interior door panel, two sizes (keep track as you remove for reinstallation purposes). You will want to remove the bottom screws first, and when you get to the top of the door panel screws, support the exterior door panel with an assistant or your off-hand. Once all screws are out, the panel should be easily removed. You can now access the Operating Module.
The Operating Module is connected to the dishwater motor via the Cable Harness. The Cable Harness is connected to the Operating Module by two plugs. Disconnect the Cable Harness by depressing the outer area of the plugs, you do not need any tools. Once these are disconnected, notice how the wiring is is routed (take a picture) and you can remove if you are also replacing the Cable Harness (I ordered just in case but did not have to).
The Operating Module is held in place by a number of plastic clips, that when depressed, will release the unit. You may need something to depress the clips (standard screwdriver) but be careful to take your time to do not force. My unit is 8 years old, and the plastic is more fragile now and these are easy to break. After trial and error, I actually started in the middle of the Module and the worked to the outside of each end to remove it. Reinstalling is a breeze (as long as you don't break the plastic clips), follow your steps in reverse. Allow 45 minutes for the whole process, but take whatever time is necessary. Much cheaper than a new dishwasher. Good Luck!
There are phillips head screws around the perimeter of the interior door panel, two sizes (keep track as you remove for reinstallation purposes). You will want to remove the bottom screws first, and when you get to the top of the door panel screws, support the exterior door panel with an assistant or your off-hand. Once all screws are out, the panel should be easily removed. You can now access the Operating Module.
The Operating Module is connected to the dishwater motor via the Cable Harness. The Cable Harness is connected to the Operating Module by two plugs. Disconnect the Cable Harness by depressing the outer area of the plugs, you do not need any tools. Once these are disconnected, notice how the wiring is is routed (take a picture) and you can remove if you are also replacing the Cable Harness (I ordered just in case but did not have to).
The Operating Module is held in place by a number of plastic clips, that when depressed, will release the unit. You may need something to depress the clips (standard screwdriver) but be careful to take your time to do not force. My unit is 8 years old, and the plastic is more fragile now and these are easy to break. After trial and error, I actually started in the middle of the Module and the worked to the outside of each end to remove it. Reinstalling is a breeze (as long as you don't break the plastic clips), follow your steps in reverse. Allow 45 minutes for the whole process, but take whatever time is necessary. Much cheaper than a new dishwasher. Good Luck!
Other Parts Used:
-
Randall from APPLE VALLEY, MN
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Screw drivers
2 of 2 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
- < Prev
- 1
- Next >
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Related Parts
Model Cross Reference
This part works with the following models:
PartSelect Number: PS8729251
Manufacturer Part Number: 00628468
Manufacturer Part Number: 00628468
Brand
Model Number
Description
Get in touch, we're here to help!
1-866-883-8386
Monday to Saturday
8am - 8pm EST