Average Repair Rating: 4.6 / 5.0, 14 reviews.
What's this?
< Prev
1
2
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
The seals on the doors were shot so the refigerader was sweeting.
I started with the freezer door. I lifted the old gasket from the inside edge to get to the hex head screws that attach the plastic inside liner to the outer door. I did not need to start at any one point so I picked a screw and removed it then I worked my way around the door. I was careful to not drop the liner when I removed the last screw. I removed the liner and pulled the old seal out of its seating grove and replaced it with the new seal. Then I used a hair dryer to fix a few places where the seal was deformed from the packing. The heat helped to get the magnetic seal back into the correct shape. I only had one corner to fix the rest of the seal was fine right out of the box. I applyed a little sealer just as the instruction said to do and then reinstalled the linner and new seal. Then I went through the same process for the refrigerator door. Not a hard job just a lot of screws to remove and then put back. The seal its self took about five minutes. Thanks for the parts!
I removed the broken supports months ago. So, I merely screwed both cover supports into place. The end caps slid into place. Piece of cake. I can't believe you had the parts for our 22 year old refrigerator. You guys are awesome!
I took the door shelf and snapped on the bracket and slid it into place. The inside door bin just slid into place. It took me longer to do a search and find the parts than it did to replace them.
Freezer drawer rail caps and crisper drawer supports were broken
I removed the old parts, installed the new parts and reassembled the crisper drawer and rails. For less than $50 delivered I was able to bring the unit back to service for our family.
Two of the end caps of one shelf and one of another were broken
Ordered the pairs of end caps for both the door shelves. The parts arrived the next day. Opened the wrapper slid the end caps on and attached the shelves to the door. Bingo!!! It was that Easy! Done in less than two days and less than $20. It took me some time to figure out if the parts were right though when I searched online.
Snapped the end caps onto the existing shelf, and eased the assembly into the door slots. Light tapping with a hammer was required to fully seat the assembly into the door. All in all, a straightforward and simple repair.
Ask our experts a question about this part and we'll get back to you as soon as possible!
2 questions answered by our experts.
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Barbara
August 7, 2019
How do you adjust the legs to make unit level
For model number FPD17TFW0
Hi Barbara,
1.Remove the base grille. Some model have screws holding the grille in place, remove screws. Some models have clips that snap out when the grille is pulled out.
2.Insert a flat blade screwdriver into the slots on the leveling leg and turn clockwise to raise the refrigerator or counterclockwise to lower it.
3.The front of the refrigerator should be 1/4 inch higher than the rear. This should be measured using a level.
4.Replace the grille.
Thank you for your question and good luck with your repair!
Was this helpful?
Thank you for voting!
Charlotte
November 12, 2019
I need to know which shelves do i need. They go on the right side of door.Also they look like they would snap i’m ??? thank you
For model number FRT21INLH Frigidaire
Hello Charlotte and thanks for writing.
Bin Part Number: PS422861 is in the list of compatible items for your model. We hope this helps. Please contact us anytime.
Fresh Flow Produce Preserver is made for your refrigerator to help keep produce fresh for longer by absorbing the chemical, ethylene, that causes your fruits and vegetables to ripen quicker. Your produce could be fresh f...
This front load washer cleaner removes odor-causing residue. Use it once a month and it will keep your machine fresh and clean. Package comes with 3 tablets.
This solid element restorer is for ranges and cooktops. Solid element restorer restores and protects solid elements from rusting and spotting. Follow the instructions on the label when using this product.
This low-odor gel, easily cleans away tough burnt-on deposits at room temperature. Apply the gel evenly on the cooled oven surface. Leave the gel to set overnight then wipe away with a clean cloth.
Make your cooktop shine with Frigidaire ReadyClean Glass and Ceramic Cleaner. Our scratch-free, streak-free formula removes smudges, grease, burnt-on food, dirt and oil, while protecting and polishing to repel dust and d...
Model Cross Reference
This part works with the following models:
PartSelect Number: PS467698
Manufacturer Part Number: 5303323480
