This part is the replacement electronic control board for your gas range. It is approximately 11 inches by 4 inches. The control board monitors the temperature and allows you to control the oven heat. If the touchpad will not respond, your oven will not start, or if you are having difficulty controlling the heat, you may have an issue with the electronic control board. Be sure to disconnect power from your range before you begin this repair. This is an OEM part sourced directly from the manufacturer.
How Buying OEM Parts Can Save You Time and Money
Troubleshooting
This part fixes the following symptoms:
Touchpad does not respond | Will Not Start | Little to no heat when baking | Will not program
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
★★★★★
★★★★★
Alanna B - January 22, 2019
Verified Purchase
Great!
Easy to install and now my oven is open! I was quoted $400+ by GE, this saved me over $200!
< Prev
1
Next >
Customer Repair Stories
Average Repair Rating: 4.2 / 5.0, 10 reviews.
What's this?
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
A lightining Strike fried the circuit board
A G.E. tech came out and quoted $500 to replace the circuit board. I unbolted the board myself and used the camera in my phone to take a picture of the wiring. Then I came to PartSelect.com and using their diagrams found the replacement board for $75. It came in the mail a few days later. I used to picture in my phone to reconnect all the wires, bolted everything back up and baked some cookies. Thanks PartSelect for making my repair job simple and inexpensive.
Other Parts Used:
Timothy from Forney, TX
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Screw drivers
25 of 31 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
electric storm fried oven display
I ordered a new display from the internet. I removed the panel where the display is housed, unscrewed the entire display assembly and unplugged all wires connecting it. (I made a drawing and noted colors of wires) I removed adhesive face of display and replaced it on the new display. I then screwed in the display and reconnected the wires as per my notes. I reassembled the panel and applied power and it worked like new.
Other Parts Used:
Sharon from Beverly, NJ
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Screw drivers
11 of 12 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Clock wouldn't keep time
Removed the top back cover. Then removed screw for clock circuit board. swapped wires from old circuit board to new circuit board. reinstalled screws. Then replaced top back cover.
First I tested oven sensor which checked o k. I then made a diagram of the electrical wireing to the oven control. I disconnected wireing and removed the control then with sharp knife I removed touch control pad. I placed th touch pad on the new panel and installed panel and connected wiring. Pluged into wall rec and test oven which checked o k .
Other Parts Used:
Richard from West Point, MS
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver
7 of 10 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The display went blank
First I removed the back panel and then removed the four screws that hold the display board in place.I then disconnected the wires. I installed the new board and connected the wires. I put the back panel on. I installed a serge protector and pluged in the range. Job completed and it worked.
Other Parts Used:
Eric from Fort Walton Beach, FL
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Pliers, Screw drivers
7 of 7 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Control panel stopped working
Very easy install of done correctly. When you pull range out,watch the gas line and don't pull it out of it's fittings. Two small Phillips head screws on the front panel low to the sides. Then two 5/16 screws on the top back panel and flip it forward. Rest it on the stove and the control panel is facing you. I'm a 30 year Electrician so please take my advice and make a schematic of the wire colors and the NUMBER associated with that color wire. Once that is done remove all wires and also a green ground wire that is under a screw. The new panel may NOT have the exact same configuration but the NUMBER on the terminals will be the same. Plus all color wires to the appropriate terminals and reinstall !! Great job!!
Other Parts Used:
Robert from BENNINGTON, VT
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Screw drivers
5 of 5 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
main controll panel quit operating oven
bought new panel and installed and looking @ wire connections from old control, I'm very much mechanically inclined , so was a breeze for me, but non handy people may not know how to disassemble the control panel without not having an idea how it's made. I'm a "mr fix it", "jack of all trades" kinda guy and am proud of it.
Other Parts Used:
Jim from muskegon, MI
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers, Screw drivers
4 of 7 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Oven would not come up to temp/retain at temp
Very simple repair, removed the back plate, took off the 4 screws holding the controler panel on, swapped over the wires one at a time, and reinstalled. Less than 15 min total time.
Other Parts Used:
Ken from Painted Post, NY
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers, Socket set
3 of 4 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Oven bake button would not work.
Simple swap and go.Several wires had different locations but every thing was marked well on both panels.Did one wire at a time.Took about 45min from pulling out oven to pushing back in.Just wish I had known about your site years ago.
Other Parts Used:
Richard from LITTLE ROCK, AR
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
3 of 3 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Lightning strike. Ignitors on stove work but display for oven was blank
Remove rear cover. Remove old display. Remove one wire (and place on new board) at a time. Carefully remove faceplate from old board and place on new one. Close everything up and your done. Took 10-15 minutes.
Other Parts Used:
Jeremy from Wilmer, AL
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver, Screw drivers
2 of 4 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
< Prev
1
Next >
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
11 questions answered by our experts.
< Prev
1
2
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
John
October 24, 2017
What does it mean when the stove makes a continual beep and the lcd display reads "bad line"
For model number RGB745BEH2CT
Hi John, Thank you for the question. A bad line error on this range indicates that the control board does not detect the proper electrical connections to the range. Check your house breakers first. If they are fine,then unplug the range (or shut off the breakers) and pull the range out. Check the wiring connections on the terminal block on the back of the appliance where the power outlet plug is connected. If the wiring on the terminal block is okay then you may want to check the voltage through the electrical outlet for the range if you have a volt/ohm meter. If there is the correct amount of volts going tot he appliance the Gas Oven Electronic Control/Clock may need to be replaced. Hope this helps!
6 people found this helpful.
Was this helpful?
Thank you for voting!
John
October 21, 2017
When oven pre heating will make loud continual beeeep and say "bad line" or sometimes "f4". Sometimes it beeps and says "18" and everything lights up on the touch pad. If i replace the touch pad control board will that fix it ? And does the plastic touch pad cover ( # 128 on the schematic ) come with it ? Ours has holes in where it cracked. Thanks - john
For model number RGB745BEH2CT
Hi John,
Thank you for your question. It could be both of those parts that are the issue. However, the F4 error code means that you oven temperature sensor has shorted and needs to be replaced. I would suggest just quickly testing that sensor before changing out your touchpad and your control board. You can test it with a multi meter. When testing the probe, if your meter does not change from the neutral position or number, then you will have to change out the probe. I hope that helps. Good luck with your repair.
2 people found this helpful.
Was this helpful?
Thank you for voting!
Scott
December 4, 2017
Have two of these stoves, one will not hold steady oven temperature. This has done this before so I replaced this following part and it fixed it for about 10 months. Hotpoint range/stove/oven igniter.Should I retry this same part again ? The other one has the display blank unless you are using the oven then it displays.What part may be the fix for this one ?
For model number RGB746WEH1WW
Hi Scott, Thank you for the question. For the oven not holding a steady temperature, before replacing the igniter again try to test the oven sensor, PartSelect Number: PS236043.Testing the temperature sensor probe on your oven is easy. With the sensor at room temperature, measure the resistance between the two prongs at the end of the sensor connector. The resistance of the sensor should read approximately 1080 – 1090 ohms at room temperature. For the appliance with the display issues, sounds like a defective Gas Oven Electronic Control/Clock, Part Number: PS3486627. Good luck with the repair!
1 person found this helpful.
Was this helpful?
Thank you for voting!
David
August 13, 2017
My oven doesn't seem to hold the temp works but takes longer to cook any thoughts
For model number RGB745EEH1BB
Hi David,
Thank you for your inquiry. If your oven is not heating evenly there are a few parts that may fix the issue for you. You may need to replace the flat style oven igniter, the oven sensor and the burner with igniter. I hope this helps with the repair. Thank you and have a great day!
Was this helpful?
Thank you for voting!
Willy
November 5, 2017
We had a problem with a bug. I removed the board and cleaned it. The first time I did it the board worked fine. I had to remove it again and now am getting a code f7 and 12 flashing code.(I could not find a 12 code in any of the web sites). I know that we might need to replace the board but want to be sure that it needs to be replaced. One of the sources said that one or more of the buttons maybe stuck down. What do you think?
For model number JGB282DET1BB
Hi Willy, Thank you for the question. You can use a hair dryer to warm the touch pad up and rub it with a dry clothe to see if there is a stuck button.If this does not fix the issue the board will need to be replaced. Hope this helps!
Was this helpful?
Thank you for voting!
Daniel
December 2, 2017
What does it mean when F4 shows up on the control panel screen when i try to use the oven
For model number RGB745BEHCCT
Hi Daniel,
Thank you for your question. The F4 error code means: Open or Shorted Oven Temperature Sensor (RTD) - Check sensor harness and connection between oven sensor and oven control. Test your oven sensor with a multi meter. If the sensor is okay, and if wiring is ok, replace control board (clock). Good luck with your repair.
Was this helpful?
Thank you for voting!
Glenn
April 26, 2018
The oven and broiler won't turn on. The oven will heat up when self cleaning is turned on. The rest of the control panel and clock work. What does this mean?
For model number JGB3000ER4WW
Hi Glenn, Thank you for the question. If the elements turn on and heat up during the clean cycle but not during the regular bake and broil, I suggest replacing the oven control board. Hope this helps!
Was this helpful?
Thank you for voting!
Jeromy
July 16, 2019
After a leak in roof, when i plug in the oven the bake light is flashing and i cannot turn on the oven or do anything with the control pad. Do i need to replace control panel and board?
For model number JGBP87SEM1SS
Hello Jeromy, thank you for inquiring. You will want to replace this Electronic Control part PS3486627 for your model.
Was this helpful?
Thank you for voting!
Jacob And Jessica
June 27, 2021
My + button wasn't working. I opened back looked for ribbon but none to be found. Than I noticed the little plastic tab that I guess exerts the pressure on the actual button had disconnected. While trying to get it out another came loose on the off button. I carefully put them back in place. Now the + button is working but not the off button - even when I depress the actual white piece inside it does not work and wont turn off. If I do have to replace control tab can I also get a new front/face panel and will the wiring match up easily? And if course will this fix my oven button problems?
For model number JGBP33WEH1WW
Hello Jacob and Jessica, Thank you for the question. The tabs are part of the housing and are only sold as part of the Oven Electronic Control board, PartSelect Number PS3486627. They should not come free from the housing and board. This board can be used with the Panel you have on the appliance and is the same as the one on the appliance. The Overlay sticker that sticks to the front PartSelect Number PS953663 has been discontinued and is no longer made sorry. We hope this helps, good luck with this repair!
My oven and broiler quit working. The surface burners work fine. How do I know if the bad part is the oven control board or the gas valve regulator. The touchpad beeps and the lights say that the oven is preheating, but it is not.
For model number rgb745wehaww
Hi Alan, thank you for reaching out. If the touchpad on your range is beeping, it most likely indicates a faulty control board, part number PS3486627. You can test the control board and the gas valve regulator with a multimeter for continuity. If you require assistance to place an order, please contact customer service. We hope that helps!
Fresh Flow Produce Preserver is made for your refrigerator to help keep produce fresh for longer by absorbing the chemical, ethylene, that causes your fruits and vegetables to ripen quicker. Your produce could be fresh f...
Having a problem with a funky-smelling washing machine, or one that just doesnt seem to clean your clothes as well as it used to? Say hello to the Affresh Washing Machine Cleaner by Whirlpool. This powerful washing helpe...
Affresh dishwasher Cleaner is specially formulated to help remove limescale and mineral build-up that can be unsightly and could affect your dishwasher's performance. Each tablet is designed to clean inside your machine ...
Make your cooktop shine with Frigidaire ReadyClean Glass and Ceramic Cleaner. Our scratch-free, streak-free formula removes smudges, grease, burnt-on food, dirt and oil, while protecting and polishing to repel dust and d...
[{"position":0,"name":"Home","title":"Home","url":"/"},{"position":1,"name":"Circuit Board or Touch Pad","title":"Circuit Board or Touch Pad","url":"/Range-Circuit-Boards-and-Touch-Pads.htm"},{"position":2,"name":"WB27K10355","title":"WB27K10355","url":""}]
