High Limit Thermostat and Thermal Cut-Off Kit Specifications
Also known as Thermal Cut-Off kit. The thermostat acts as a safety mechanism that keeps the dryer from overheating and the fuse is like a backup system - it's set to trip at a higher temperature than the thermostat. Once it trips, it has to be replaced.
How Buying OEM Parts Can Save You Time and Money
Part Videos
Replacing your Whirlpool Dryer High Limit Thermostat and Thermal Cut-Off Kit
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
★★★★★
★★★★★
LEE G - August 13, 2020
Verified Purchase
Easy repair
Tha parts arrived very quickly, and were in perfect condition. The customer service representative was very knowledgeable, and the videos were so helpful. I will order from here again.
★★★★★
★★★★★
Dick S - September 12, 2018
Verified Purchase
Got what I needed
Came unbelievably fast. We are up and running. Thanks so much
★★★★★
★★★★★
François R - May 13, 2020
Verified Purchase
Great video explaining how to mount / unmount
Easy to fix with video
★★★★★
★★★★★
Dominique L - November 12, 2020
Verified Purchase
Easy to repair
Followed the instructions and everything works well
★★★★★
★★★★★
Landry S - December 4, 2024
Verified Purchase
ITS work good
Good Shap Andrès good parts tanks
★★★★★
★★★★★
Al D - April 28, 2020
Verified Purchase
Easy repair & Fast service
The part was delivered as expected very efficient company to deal with in all ways We will definitely deal with this company again if we are in need of any future parts
★★★★★
★★★★★
Raidel H - April 28, 2020
Verified Purchase
Worked as expected.
The part arrived in good condition and faster than expected.
★★★★★
★★★★★
David M - December 20, 2021
Verified Purchase
Easy repair, Prompt Delivery
Delivery was prompt. The accompanying video went a bit far on disassembly but would make it clear for those who've not done anything like this before. Thank You
★★★★★
★★★★★
LAURA D - May 20, 2021
Verified Purchase
My tenant put it in! He’s handy.
But he said it was super easy to install. it works like a charm. This company ROCKS! The website says 3-5 business days, but my experience has been 1-3 days. Great customer service, very friendly and knowledgeable.
★★★★★
★★★★★
BARRY T - November 6, 2021
Verified Purchase
Solved my Problem
Parts are of superior quality, Quick delivery and easliy installed.
< Prev
1
2
Next >
Customer Repair Stories
Average Repair Rating: 3.5 / 5.0, 14 reviews.
What's this?
< Prev
1
2
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
My Dryer Was Not Heating Up.
I asked for advise, looked around and priced heating elements and thermostats. This was the best combo offered for the price given. It was shipped and received it very quick. Installed it and 5 minutes later, she was running like a champ!
I simply removed the back of the dryer to gain access to the heating element. Once I removed the heating element I figured I would also replace the thermostat and thermal fuse as preventive maintenance.
First i tested each part for continuity and found out that the thermal fuse was bad. So ordered the part and went ahead and got thermostat and element to ensure no problems in the future since I already was in there.
I replaced the thermistor earlier, but the code was still flashing. I noticed the heater terminals were charred and pretty well covered in carbon. So, I replaced the heater, the thermostat and thermal fuse and replaced the 3/8" spade terminals on the heater wires. (These are hard to find - most electrical spades terminals are .250. Also, I crimped and soldered these for a connection with the lowest resistance possible). After all that, the code still flashed! I let the explatives fly, calmed down, and ran the control board test. (This is done by pressing "more time" "less time" "more time" "less time" in succession.) The control board was passing all the tests, but the thermistor test, and the only thing is in this circuit is the thermistor, the wires, the connector to the control board, and some circuit on the control board that involves a few resistors and the "brain" chip. So, I checked the terminals at the thermistor, the wires up to the control board and the connector at the board. The control board connector was fairly dust encrusted, so I unplugged it, cleaned the control board terminals and sucked away all the lint and dust. Finally, I carefully removed earch crimp terminal from the Molex connector (the white female connector) and cleaned and bent them to yield a better connection to the terminals on the control board. I put it all back together, and thus far it is working fine.
Other Parts Used:
John from Cedar Rapids, IA
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Pliers, Screw drivers
19 of 28 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Dryer working fine but no heat
Found this website and reviewed videos and comments prior to purchasing the heater element and high limit thermostat and thermal fuse kit. We had recently put our Whirlpool duet washer and dryer on pedestals and after that, the dryer would come on and run, but would not heat up. Installation of the parts we ordered was simple...and we would be considered novice installers....really great website and easy to understand. Customer service was excellent as well. After installation of the parts, still no heat and heating element was registering only 120v. We checked everything again and found that the dryer plug was not all the way in the socket. Probably came loose with the move to the petestal.....plugged it in securely and it works great now. Should have checked that first, but because it was running we just didn't think of checking it. Good lesson learned and so glad we found this website. We will definately be using this site again and telling everyone we know about how great you guys are! And at least we won't have to worry about the dryer for a while and we now know we can fix a dryer that won't heat up!
Open breaker and ensure power was off. Checked heating components for continuity.Found thermal fuse had an open circuit.Replaced High limit thermostat and thermal fuse.Now is a good time time check for free flowing vent piping.I discovered mine was crimped below the floor and caused lint build up and obstructing the flow which could have led to the thermal fuse blowing.I replaced the vent piping as well.My wife says the dryer works better now than it ever has.
take off front bottom panel. use ohm tester on the heater coil element, (It had broken in back) remove screw holding it in place and the two red wires leading to the element. Pull out and replace. reinstall in reverse. Done
Pulled the lower front panel located thermal switch pulled 2 wires removed 2 small bolts pulled switch out set meter to ohms scale and tested between the 2 terminals it hailed the test I reversed for installation of new switch
Other Parts Used:
kevin from RENTON, WA
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers, Socket set
6 of 6 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
No heat
Took the back off the dryer. Found heating element unhooked the electrical connectors to the element,the high temp thermostat and the fuse backup. Opened the front kick plate, took the casing with element, ht thermostat and fuse bu out. Changed all three parts and reinstalled them. Turned on dryer and had heat. Been working great ever since.
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
30 questions answered by our experts.
< Prev
1
2
3
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Anthony Price
March 5, 2018
My Whirlpool duet dryer is not heating and there are no codes. The dryer did the whole cycle and the clothes were still wet. Could this be the heating element or is there another part that could be faulty? This is the first time my dryer has not worked since 2005. Thanks
For model number GEW9250PW0
Hello Anthony, thank you for your question. The first thing you will want to do is vacuum the inside of the unit around the element, the tumbler, the motor and the ducting. If there are not obstructions, and the unit continues to not heat. You will want to check the thermostats. There are a couple of them on the unit; Thermal Fuse Part Number: WP3392519, High Limit Thermostat and Thermal Fuse Kit Part Number: 279973, Thermostat, Internal-Bias Part Number: WP8577274, and the
High Limit Thermostat - L295-50F Part Number: WP3391914. These can all be tested with a multimeter. Use a multimeter to test the thermostat's resistance by setting it to the RX 1 setting.
Place each of the meter's probes onto the wire terminals. You should receive a reading of 0. Resistance that is low, or near 0, means that the electrical flow is good and the part does not need to be replaced. If the thermostats test as being in good condition and working properly, the element would be the issue. I hope this helps!
20 people found this helpful.
Was this helpful?
Thank you for voting!
Chris
November 18, 2017
Dryer heat was not working, so I ordered a new heating element and installed it, but there is no heat still. I checked continuity and there is nothing with the 2 connections to the element. What next? There are a bunch of wire harnesses but not sure where a fuse may be?
For model number MEDZ600TW2
Hello Chris,
Thanks for your question. You will need to remove the bottom panel to gain access to the thermal cut-off fuse and high limit thermostat.
I hope this helps.
8 people found this helpful.
Was this helpful?
Thank you for voting!
Dan
February 24, 2018
Have replaced the thermostat and fuse twice. High limit fuse was blown initially and when replaced both times. Dryer heated but fuse blows during first load. I cleaned all ducts and checked airflow on first replacement and again on second replacement. Air is flowing freely and heating element works. I watched heating element switch on and off when on low setting.
For model number GEW9250PW0
Hi Dan, Thank you for the question. If both the High Limit Thermostat and Thermal Fuse were replaced at the same time, I suggest testing the Thermostat, Internal-Bias Part Number, PS11746740 and the Thermal Fuse, Part Number: PS11741460. These parts are located on the blower housing and can be tested with a multi meter. They should be replaced at the same time. Same as the High Limit Thermostat and Thermal Fuse should also be replaced together. Hope this helps!
7 people found this helpful.
Was this helpful?
Thank you for voting!
Ken
July 19, 2019
I replaced the thermal fuse about six weeks ago. The dryer has been working but gets very hot. I don't think there is any low heat. What do i need to do to fix this? I also noticed that on the module plate in the under the top cover one of the mods (the first one on the front end seems chared. Is this a replaceable piece.Help! don't want to burn the house down.
thank you!
For model number Whirlpool WED94HEXR0
Hello Ken, thank you for inquiring. Too much heat can indicate a defective Thermal Fuse part PS11741460 for your model. It could also be either the Internal-Bias Thermostat part PS11746740 or the High Limit Thermostat and Thermal Cut-Off Kit part PS334387 for your model. The other piece you are referring to is only sold as a part of the Console for your unit. Unfortunately the Console is discontinued and is no longer available. We have no known replacement information in our system. We recommend you contact Whirlpool directly to see if they have recently released a new substitute. Please feel free to get back in touch with us to place an order if they provide a substitution part number. Thank you.
4 people found this helpful.
Was this helpful?
Thank you for voting!
Marsha
September 12, 2019
My 4 1/2 year old Maytag dryer is not heating at all. I have had the vent checked and it is clear. I had an appliance repair guy out and he said he tested all the usual parts (fuses etc) and they all were good. He now says it has to be the mother board, which seems out of line for a 4 year old dryer. Could he be right?
For model number MEDB725BW0
Hi Marsha,
Thank you for your question. If the technician you hired tested the usual parts and they checked out fine, it is possible that the electronic control board may be the issue. To verify if it is the part causing the issue, you will need to test the parts with a multimeter. Here is a link to one of our videos on YouTube that you may reference on how to use one, https://www.youtube.com/watch?v=bWC44fHn0As. I hope this helps. Thank you and have a great day!
2 people found this helpful.
Was this helpful?
Thank you for voting!
Alberto
August 11, 2017
Dryer shuts off and am getting a code 22.
For model number wed9550ww1
Hi Alberto,
Thank you for the great question, This error Whirlpool uses to indicate the Thermistor shorted and needs to be replaced.
Hope this helps !
Part i got for that model doesn't look the same. Only has two terminals for wires and mine has three on my highlimit cut off. Is it the wrong part?
For model number wed8000dw3
Hello Randal, thank you for your question. This kit is the recommended replacement for your specific model. However, the part has been substituted from the original. Per the manufacturer this kit will still work for your unit. I hope this helps!
2 people found this helpful.
Was this helpful?
Thank you for voting!
Rich
November 4, 2017
My dryer Whirlpool has f01 code and will not start. How do i put it in the diagnostic mode
For model number WED9400SW2
Hi Rich,
Thank you for your inquiry. The F01 indicates a failed electronic machine control board. This error code can sometimes be caused by a glitch or power surge through the electrical lines. You may be able to clear this code by unplugging the washer for 5 minutes. Be sure to unplug the washer before accessing internal components. If this does not help you will need to replace the electronic control board. I hope this helps. Thank you and have a great day!
1 person found this helpful.
Was this helpful?
Thank you for voting!
John
January 27, 2018
I purchased p/n wpl 279973 and am trying to find an installation video.
For model number WED8300SW2
Hi John,
Thank you for your question. It looks like we have an installation video posted underneath the part information. Here is the link for you: https://youtu.be/GDQLr2EXogo . Good luck with your repair.
1 person found this helpful.
Was this helpful?
Thank you for voting!
Richard
July 17, 2019
Good afternoon. My dryer would not start (although the lights came on) so I replaced the thermal fuse (WP3392519). The dryer started and worked for a day, then, as above would not start again. I checked the resistance on the fuse - there was no connectivity. There are no obstructions in the unit or the exit hose / vent. It was suggested that I replace the thermal cutoff with 279973. Prior to doing so, I tested the connectivity on the two parts. Both showed connectivity except when I heated the thermostat in an electric skillet. If 'clicked' off at 280 degrees Celsius. I have not checked the other part included in 279973 (another thermal fuse?) other than to verify that it has zero ohms of resistance. Not sure what else to check prior to replacing the 279973; however, the thermal cutoff is good, I would rather not spend the $50. Help? Next steps?
For model number YMEDE300VF1
Hi Richard,
Thank you for your question. If you have not checked the other thermal fuse, I would check it with a multimeter to verify if it is working correctly. If the dryer is not starting there are some other parts you should also check as well to see if they are causing the issue. I would also check the door switch, the start switch, the motor, the electronic control board and the terminal block. I hope this helps. Thank you and have a great day!
When connected to electricity the dryer heating element glows red hot and generates heat. When air is blown over it, it heats the air which is used to dry the clothes. The heating element fits inside the heater housing i...
This part is a one-time use thermal fuse which attaches to the blower wheel housing of your clothes dryer. It cannot be re-set and must be replaced when there is no longer continuity between the pins. Terminal size is 3/...
This thermostat may differ in appearance, but functions the same as the original part. This part controls the temperature of the inside of the dryer drum and prevents the dryer from overheating.
Fresh Flow Produce Preserver is made for your refrigerator to help keep produce fresh for longer by absorbing the chemical, ethylene, that causes your fruits and vegetables to ripen quicker. Your produce could be fresh f...
Having a problem with a funky-smelling washing machine, or one that just doesnt seem to clean your clothes as well as it used to? Say hello to the Affresh Washing Machine Cleaner by Whirlpool. This powerful washing helpe...
Affresh dishwasher Cleaner is specially formulated to help remove limescale and mineral build-up that can be unsightly and could affect your dishwasher's performance. Each tablet is designed to clean inside your machine ...
Make your cooktop shine with Frigidaire ReadyClean Glass and Ceramic Cleaner. Our scratch-free, streak-free formula removes smudges, grease, burnt-on food, dirt and oil, while protecting and polishing to repel dust and d...
