Light Socket WR2X9391

I have a fridge in my garage. I have found that a glass of ice water or a cold drink outside is very important to me. When I discovered melting ice dripping onto the garage floor I was very upset. I spun the fridge and found that the compressor and fan weren't starting. I got out my multi-meter and discovered that power was not making it to these components. I did some research and found the wiring diagram online. There really isn't too much going on with a fridge and the most likely candidate seemed to be the run capacitor. I ordered the part, replaced it in a few minutes and the fridge began working again.

unplugged refrigerator. removed light bulb from old socket. unsnapped old light socket and pulled it out just enough to diconnect the electrical plug that plugs into the socket . discarded the old socket and plugged in new socket. snapped in new socket into refrigerator. i watched how to do this simple procedure on you tube and decided to do it myself. easy easy easy

First turned off power and removed top shelf.
Then I used a flathead to slowly pry the switch out by the two sides. You just anlge ita bit and it slideds out easily. Then I disconnected the wires from the old switch, connected the new one and installed the new switch by snapping it back into the cutout.

After I bought what I thought I needed for the repair. I asked a friend to come over and look at it. He changed the
the light socket and put the same light bulb in and it works great. I am returning the light switch but decided to keep the light bulb.

Getting on the internet was so easy. This was really very simple. Thank you for making what I thought would be a big ordeal into something very simple.

Paulette Johnson

To repair the light socket which was not functioning, I identified and followed the instructions on part-select on you tube. I unplugged the refrigerator, cleared away and removed the shelf below the housing for the light. I reached up under the plastic light protector with a screwdriver and popped up the tab on the front holding it in place. Then I easily pulled out the defective socket. I reversed the process and popped the new one in to replace the old, screwed in the light bulb, put the shelf back, plugged the fridge in and was finished. This took only about 5-10 minutes. To repair, and replace the dual inlet-water valve, I pulled the refrigerator out and removed all the nuts protecting the back at the bottom. I unplugged the fridge and turned the water switch at the wall to off. I once again had identified the problem by the symptoms on part-select, ordered the part and watched and followed the repair on part-select on you-tube. There are a variety of nuts and bolts to remove the protective housing and then get to the water inlet valve unit at the back left bottom side. It doesn't take long. I unplugged the two electrical lines holding the water inlet valve in place, I unscrewed the bolt in the center on top and the two valves underneath that are the three water lines from the water in the refrigerator back to the unit and on to the ice maker. I replaced the unit as instructed and started to reconnect the hoses. At that time, I noticed that the hose from the unit to the ice maker was a little brittle at the end. So, I suggest you check all your hoses as well when you identify the same problem. I decided it would be best to replace the hose as well and ordered the ice water hose from part select. I left the water off and put the fridge back. The ice maker hose replacement came quickly, in 2 days. Then I simply pulkled it out and replaced that ice water line in about a minute, reversed putting back the rest of he screws that hols everything in place, closed up the unit, plugged the fridge in, turned on the water valve at the wall and put the refrigerator back in to place. This process, if uninterrupted, would take about 30 -45 minutes. Everything is working good as new now. I probably saved myself at least 150 dollars, had the satisfaction of fixing it and learned something myself about how the whole thing functions. Part select is a find!

pulled the lightsocket back and down and took out bulb an unplugged. replaced with new socket nd put back in refrigerator and was missing roller in dishwasher. On that part all i had to do was push the clip onto the little bar and push the roller in

It just unpluged and the new one plugged in. Simple. The part was reasonable and arrived very quickly. It sure is nice to have a light in the frig again.

turn breaker off first then use thin blade screwdriver and plastic pry bar to remove light socket and switch there was plenty of wire so work was easy to install at both ends

Took out the light sockets, plugged in the new ones. I found the manual on line to find the part numbers. Parts select parts were perfect

1- youtubed the potential diagnoses, 2- resourced and ordered parts, 3- removed old socket, installed new one :-)... My fridge is an older fridge and could've used a screwdriver for eyeglasses. Plug and play easy... YAY!