Control your cooktop’s heat with this genuine infinite surface element switch, designed to regulate power to individual burners for precise temperature adjustment. Operating at 1250W and 240V, it allows smooth transitions from low to high heat for consistent cooking results. This durable OEM component helps resolve issues such as burners not heating, overheating, or delivering uneven heat. Installation is simple—disconnect power, remove the faulty switch, and secure the new one in place for reliable performance.
How Buying OEM Parts Can Save You Time and Money
Troubleshooting
This part works with the following products:
Range, Cooktop.
This part works with the following products:
General Electric, Kenmore, Hotpoint.
Part# WB24T10022 replaces these:
AP2024071, 769689
Customer Reviews
Average Rating:
★★★★★
★★★★★
1 Review
5.0
Filter By Rating:
5 Stars
1
4 Stars
0
3 Stars
0
2 Stars
0
1 Star
0
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
★★★★★
★★★★★
Francois C - November 24, 2021
Verified Purchase
Control
Good product
< Prev
1
Next >
Customer Repair Stories
Average Repair Rating: 3.9 / 5.0, 1 reviews.
What's this?
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
Switch and burner dead
Removed rear panel, disconnected wires, unscrewed switch X2 - installed new parts in reverse order. Note: Would have appreciated new mounting screws with replacement switch.
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
6 questions answered by our experts.
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Dave
December 19, 2018
Right front burner ,goes way above set point,and will not adjust down until knob is turned to off then back on again, do i need a new switch?
For model number 911.93141000
Hi Dave,
Thank you for your question. If the temperature of the burner is going higher than it should, than you will need to replace the burner switch. I hope this helps. Thank you and have a great day!
2 people found this helpful.
Was this helpful?
Thank you for voting!
Kevin
December 6, 2018
The burner light stays on even when the burners are off.
For model number RB526DH2BB
Hi Kevin, thank you for your question. It sounds like you may need to replace the light itself. I hope that helps. Good luck with your repair.
None of the 4 burners will get red hot, I have swapped the burners to another stove so I know it is not the burners. I dont see how 4 switches can be not working, what else can it be?
For model number J bs160D m3ww
Hi Robert, thank you for the question. You may need to check the surface element terminal block kit, part number PS783534, to fix the issue. It connects the wire harness to the surface element. We hope this solves your problem!
The four burners' temperature gets hotter than what I set it to. I have to turn them off and then back again to get them to come down. The stove also makes a buzzing sound when on. No problem with the oven.
For model number RB526DH1WW
Hello Teresa, thank you for reaching out. According to our research, we would recommend checking the wiring connections between the surface element control switches. If the connections are fine, the issue is most probably with the surface element control switches. You may need to replace them to fix the issue. The 8 inches surface element control switch is part number PS236752, and the 6 inches surface element control switch is part number PS236747. It turns the surface element on and off and controls how much heat the element produces. We hope this helps!
All 4 of my stove top burners all the sudden stop heating, and all at the same time, could there be a fuse on this model or a switch that controls all 4 burners that went bad on me. Thanks for the help.
For model number RB525C2WH
Hello Jonni, thank you for contacting us. All the burners and switch meet at the terminal block, it would be the only part that would cause all 4 burners to go at once. The part number for the terminal block kit is part number: PS242972 Hope this helps!
Was this helpful?
Thank you for voting!
Carlton
February 8, 2018
Right front burner will not heat replaced the block and burner
For model number RB526K1BB
Hi Carlton, Thank you for the question. If the new element did not fix the issue. I suggest replacing the switch that controls the burner. Hope this helps!
Fresh Flow Produce Preserver is made for your refrigerator to help keep produce fresh for longer by absorbing the chemical, ethylene, that causes your fruits and vegetables to ripen quicker. Your produce could be fresh f...
Having a problem with a funky-smelling washing machine, or one that just doesnt seem to clean your clothes as well as it used to? Say hello to the Affresh Washing Machine Cleaner by Whirlpool. This powerful washing helpe...
Affresh dishwasher Cleaner is specially formulated to help remove limescale and mineral build-up that can be unsightly and could affect your dishwasher's performance. Each tablet is designed to clean inside your machine ...
Make your cooktop shine with Frigidaire ReadyClean Glass and Ceramic Cleaner. Our scratch-free, streak-free formula removes smudges, grease, burnt-on food, dirt and oil, while protecting and polishing to repel dust and d...
