Drain Pump - 60Hz 120V 137108000

After turning off water, disconnecting power, and sucking water out of the tub and drain hose with a shop vac, I removed the front kick panel (took out two sheet metal screws). Then I removed two mounting screws from the pump assembly, and disconnected two hose clamps (inlet and outlet hoses) with a pair of pliers. Very simple, very easy. The pain in the fanny came when I tried to reattach the hoses. The hose clamps apparently require either a special tool or a technique I'm not familiar with. I finally tossed them and purchased two standard screw and band hose clamps which made the final connections a breeze. The surprise came when I found that the motor had seized because of a pair of tweezers that had somehow worked into the motor impeller. Free of tweezers and coins, the new motor works great! To quote another one of your contributors: wife happy!

First I turned off the breaker to the washer.

Then I removed the drain pump motor, saw that it was broken, and ordered a new one with expedited shipping. It was delivered about 36 hours later.

I should have used my wet/dry vac to suck out all of the water remaining in the drain lines. Because I didn't, nasty water dripped all over my laundry room. Lesson learned!

The part arrived at 2:20. I had to pick up my kids at school at 3pm. I wasn't sure I'd have time, but I tried anyway. I first removed the screws holding the entire pump assembly to the floor of the washer. Then I attempted to remove the clamps holding the three hoses onto the pump / motor assembly. I tried with regular pliers for about 10 minutes and finally realized I needed locking pliers. Mine are missing, but I have a stone mason doing a project at my house. I borrowed his and immediately had the clamps loosened. I slid them back onto the hoses, inserted the pump motor into each hose one by one, and reattached the clamps.

I ran a little water into the washer, checked to see that it didn't leak upon draining, then started a load and left to get my kids from school.

This was a very easy repair. The part was $75 plus about $20 for the expedited delivery. The Sears service call would have been $65 just to walk in the door PLUS whatever they would have charged me for the labor and the part. I am guessing I saved over $200.

The worst part was the gross water remaining in the drain lines. This would have been easily avoided if I'd just taken the time to get the shop vac. Learn from me and don't skip this step!!

disconnected the power cord,removed two screws on lower front edge of machine, removed lower front cover. Got the wet vac ready to suck up the water in the rubber boots when I took the clamps off. Disconnect the pump wires, and two bolts that mounted the pump. wrestled off the boots, and cleaned out the junk in the bottom of the main boot, sucking up water as the boots came off. then reversed the process. Not bad at all. Makes you want to double check for coins so they don't destroy the pump impeller.

Vibration/Shock: remove front cover, to remove the shocks depress the tab on the locking pins and push out. Install new shocks and pin in reverse order.

Pump: Disconect power, remove front cover, slowly remove clamp from discharge side of pump and use a sponge or rag to collect water. About one pint will remain in the upper hose. Remove the upper hose after draining. Unplug the power supply to the pump and remove two screws securing the pump to the floor of the washer. Install the new pump and conect wire and hoses.

Use a cup to take the water out of the washer. Get at least three large towels -- you're going to have to sop up the water when you disconnect the hoses.

Take the bottom panel off (2 Phillips head screws). Drain pump is on the right side.

Remove the two screws holding the pump to the metal bottom plate. Use a small socket wrench and/or a screwdriver. I had to use a screwdriver on the right screw and a socket wrench on the left screw! Place as many towels in the cavity as you can to catch the water that's going to come out when you detach the hoses.

There is an inlet hose and an outlet hose, attached with bright green clamps. Remove those with pliers. Clean up the water that drains out. The hose in the back (inlet) has a "coin catcher" area. Clean this out.

Attach the hoses to the new pump. Screw it down. Replace the bottom panel.

Used a shop vac to suck all the water through the drain hose. Removed the bottom front panel held by two screws on bottom and two plastic pins at the top. Removed electric connector on front of pump. Removed two screws holding pump down. Used pliers to move spring clips back so hoses could be removed. Put hoses on new pump and squeezed clamps with pliers to pull them back over the hose connection. The connection on the left was a little bit of a pain due to space limitations. Screwed the new pump down and reconnected the electric plug. Put the bottom cover back on and screwed it into place.

NO EXPERIENCE NECESSARY!!
Unplug electrical.
Remove lower front panel -2 screws.
Locate drain pump in front right .
Remove electrical wiring plug - press release clip.
Remove mounting to floor - 2 screws.
Remove two hose clamps - pilers.
Mount in new part - 2 screws.
Reattach two hose clamps - pilers
* be sure hoses are fully reattached.
Attached electrical wiring plug.
Attach front panel - 2 screws
Plug in the electrical and be proud of your accomplishment because you just saved a minimum of US$200.00. Congrats.

First thought the problem was with the spin cycle, however it soon became clear it was the pump that wasn't draining the water that kept the spin cycle from doing it's thing. After hand-wringing a large load and shopvacing out the remaining water, I ordered the new pump, got it in two days, and did a quick change out and it works perfectly. During the removal of the rubber boot that connects the tub to the pump, the one thing I did discover was a yucky buildup of years of fabric softener which I couldn't break my wife from using. But, after showing, and more importantly, letting her SMELL the fungus/mildew in the sludge, I've finally broken her of the habit! Best bang for the repair buck so far.

first took off old pump off by removing 2 screws and removed 2drain hoses under front load washer with pair of pliers then put new pump on same as removal.

First, I unplugged the unit, then took out the hold down screw. Next I took off both snap rings and layed towels down. Pulled off both hoses. Finally reattached in reverse order. I did not have the problem of others with the snap rings they came off easy and went back on easy.