This kit comes with the terminal block, mounting clip and wires.
How Buying OEM Parts Can Save You Time and Money
Part Videos
Replacing your Kenmore Range Surface Burner Terminal Block Kit
Troubleshooting
This part fixes the following symptoms:
Element will not heat
This part works with the following products:
Range, Cooktop, Microwave Oven Combo.
This part works with the following products:
Kenmore, General Electric, Hotpoint, Roper.
Part# WB17X210 replaces these:
AP2021472, 2266, WB17X210, 291245, 293798, 293973, 293976, 299209, 304644, 304645, 306179, 318960, 326800, 330691, 343823, 343824, 4335063, 4336389, 8004683, WB17K5017
...
Show more
, WB17X10015, WB17X10017, WB17X10018, WB17X216, WB17X217
Show less
Customer Repair Stories
Average Repair Rating: 3.8 / 5.0, 3 reviews.
What's this?
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
There was no heat on the coils.
I opened the lid, and found that the terminal blocks were burnt, the wires were melted. I ordered one set of terminal block to replace the burnt one, and it worked. Before I started, I shut off the electricity in the whole house to be safe.
Other Parts Used:
Shaohui from East Lansing, MI
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers
48 of 52 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Surface burner coil did not work.
TURN OFF ALL POWER TO KITCHEN. Took off all burner coils and plates below them. Lift hood. Locate part. Remove old part and replace with new part in same way as was previously installed. The wire that comes with the kit is actually too much wire, but just arrange it the best you can and leave it....no big deal. I didn't have a magnet, but needed one. The wire from burner coil to switch runs through a harness which is screwed on to the body of the oven (below the range). Be careful NOT to drop it behind oven when taking it out. I dropped it and took forever to get it. That turned a 20 minuate job into an hour and a half. Otherwise this is an easy job that anyone can do. Refrigerator compressor is next. Have fun.
Other Parts Used:
Gregory from Mont Belvieu, TX
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Screw drivers, Socket set
23 of 33 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Old Terminal Block was arcing.
Cut Wires to old terminal block and wired in new Terminal Block
Other Parts Used:
Robert from HOUSTON, TX
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
1 personfound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
< Prev
1
Next >
Questions and Answers
Ask our experts a question about this part and we'll get back to you as soon as possible!
11 questions answered by our experts.
< Prev
1
2
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Katherine
February 18, 2019
Does this kit come with enough parts for all 4 burners
Hello Katherine, Thank you for contacting us. This is a single terminal block kit. Should you need to replace all 4 burner terminal blocks you will need to order a quantity of 4. Have a great day!
6 people found this helpful.
Was this helpful?
Thank you for voting!
Craig
September 9, 2019
Right front 8 inch burner goes red hot whenever it wants to. What is this?
For model number JBP35DMBB
Hi Craig,
Thank you for your question. If your 8 inch burner goes red whenever it wants to then the issue is the burner switch that operates it and it will need to be replaced. The part number listed under your model number for the 8 inch burner switch is PS236750. I hope this helps. Thank you and have a great day!
6 people found this helpful.
Was this helpful?
Thank you for voting!
John
October 29, 2017
It's hard to tell from the picture. Does this kit come with two wires, one for each side of the element? My stove is a very old GE profile spectra 4 burner with oven.
For model number JRP4?WC?6WW
Hi John, Thank you for the question. Yes this kit comes with 2 wires. Hope this helps!
5 people found this helpful.
Was this helpful?
Thank you for voting!
MARK
February 13, 2020
How many burners does this fix
Hello Mark, thank you for your question. This Terminal Block kit is for one one Burner Element. I hope this helps.
3 people found this helpful.
Was this helpful?
Thank you for voting!
Sandy
September 1, 2021
If you're only replacing one receptacle why do you need to undo all four before replacing the one you're replacing?
For model number RF725GOP3BG
Hello Sandy, Thank you for the question. We suggest watching the How to Video for instillation help. Good luck with the repair!
https://www.youtube.com/watch?v=9921quu0ZIw
3 people found this helpful.
Was this helpful?
Thank you for voting!
Robert
October 10, 2017
Can you get the ends for the wires, and use the wires already there?
For model number 9114628791
Hi Robert,
Thank you for your question. Unfortunately you cannot. You would have to replace this part. Good luck with your repair.
2 people found this helpful.
Was this helpful?
Thank you for voting!
Walker
February 11, 2019
Does this kit work with my model number
For model number jp326wov1ww
Hi Walker,
Thank you for your question. Yes, this kit will work on your cooktop. I hope this helps. Thank you and have a great day!
1 person found this helpful.
Was this helpful?
Thank you for voting!
Jonathan
November 25, 2022
My right front burner gets stuck on high even when i turn the temperature down to low.
Thanks
For model number J BP23S R5SS
Hello Jonathan, thank you for your inquiry. We have researched your model and found that the issue is probably caused by the terminal block kit, part number PS783534. If replacing it does not help, we would recommend replacing the element switch, part number PS236754. This switch controls the burner. Customer service is available 7 days a week if you need help placing an order. Glad to be of assistance!
My front right burner gets red hot whenever it wants to. What do I need to replace
For model number JB25ORK1SS
Hi Maria, thank you for reaching out. The element switch appears to be faulty and you may need to replace it with part number PS236750. We hope this information helps! If you need help placing an order, customer service is open 7 days a week. Thanks again for your great question.
Fresh Flow Produce Preserver is made for your refrigerator to help keep produce fresh for longer by absorbing the chemical, ethylene, that causes your fruits and vegetables to ripen quicker. Your produce could be fresh f...
Having a problem with a funky-smelling washing machine, or one that just doesn't seem to clean your clothes as well as it used to? Say hello to the Affresh Washing Machine Cleaner by Whirlpool. This powerful washing help...
Affresh dishwasher Cleaner is specially formulated to help remove limescale and mineral build-up that can be unsightly and could affect your dishwasher's performance. Each tablet is designed to clean inside your machine ...
Make your cooktop shine with Frigidaire ReadyClean Glass and Ceramic Cleaner. Our scratch-free, streak-free formula removes smudges, grease, burnt-on food, dirt and oil, while protecting and polishing to repel dust and d...
[{"position":0,"name":"Home","title":"Home","url":"/"},{"position":1,"name":"Wire Plug or Connector","title":"Wire Plug or Connector","url":"/Range-Wire-Plugs-and-Connectors.htm"},{"position":2,"name":"WB17X210","title":"WB17X210","url":""}]
