Heating Element Kit - Red Dot 61927

I couldn't find any information on the internet on how to fix my dryer, so I took every screw out of it, which I later found was not needed - just 2 in the front. Then I had to figure out WHERE the element was. Turns out, against the back panel with 2 screws. I had to crawl on my belly to get in there with little room to work. Installing the new one didn't take long at all though. I also vacuumed out the inside and cleaned it well, then put all the screws back in it.

I'm glad I re-did all the screws because now it sounds brand new. It's 3 times quieter than it ever was (it was donated to me), and it feels great that I was able to fix it on my own for about $50.

I first unplugged the dryer (don't want to get nailed with 240 volts). I then removed the two screws on the bottom section of the dryer just below the door. I then removed the two screws on the front door assembly and removed the door (make sure you don't break the wires and/or door switch. The wires need to be removed from the door switch prior to removing the door panel completely). I then took a flash light and look inside the dryer towards the back. I could see the heating element in the back. I then removed the two screws holding the heat element and removed the heating element (taking note on the orientation of the element). I then removed the black and orange wires making note which wire fit on which terminal. I then compared the old unit with the new unit to make sure I had the right one. I then assembled the new heating element (heat sensors etc.). I then hooked the black and orange wire to the new element. I then reassembled everything in the reverse order.

Note: I very CAREFULLY used the heating elements support connectors to hold the element in place while I started my screws. Once they were started then I could release the element and fit it properly into the housing as I tightened the screws.

The other thing that you need to check is to make sure that the air-duct is not blocked. If you have a lot of lent on the bottom of the dyer (inside) then you could have a blocked air-duct. This happened to me. I went outside and noticed that we have a door on our vent that flips up to keep mice etc. from coming in. Some of the lint that was blown out got wet from the sprinklers and calcified underneath the vent. This was preventing the vent from opening. This could of been our problem all along but I had already replaced the heating element so I keep it as is.

PartSelect was wonderful. I was able to find my parts quickly and the turn around time was tremendous. I would buy from PartSelect again.

This was the second time we lost the High Limit Thermal Fuse. My wife dried some new towels and the lint filter completely plugged before the cycle was done and popped the high limit fuse. I went throught this before and paid a fortune for a repairman and ended up installing the thermal fuse myself so I did it myself and saved about $100. I also ordered an element kit so I have it. I will just swap out element units if there is a next time. Maybe the next time we buy new towels. It only takes few minutes to remove the front lower panel and unplug two wires, remove two screws and the element assembly with both the fuse and the thermostat are out. It is easy to replace the fuse with the element assembly in your hands and in good light.

I removed the screws that hold the element in place. I disconnected the wires. I took the new part, which was easy to identify and order, assembled per instructions, and attached it to the wires in the dryer, then screwed it in. I normally let my husband do these repairs, but he wasn't available. It was easy and the dryer works perfectly again!

First I remove the two scews from the bottom panel of dryer to remove it. Then remove the two screws that held the element in place. I then pulled the element out about 20 inches and disconnected the two wires and re-connected to new element re-installed it. The dryer works like its brand new. No problem to install at all.

My husband removed the two screws that hold the element in place. He pulled out the old element, and replace it with the new one. Cleaning out all the lint and replacing the element took about 45 minutes.

I ordered the complete heating element, which included all three parts. My husband removed the defective one, and replaced it with the new one, and the dryer works better than ever!

i am sorry i dont know all the technical term but here it goes, first I turned of the electrical breaker to the dryer, I unpluged the dryer and disconnected the dryer hose to the outside of home, I removed front dryer panel, remove front of drum panel, removed belt and found it to be worn, removed drum, removed the wiring connected to the back panel that had heating element inside, removed the back panel, removed the heating element inside the back panel and then reassembled unit. I had question whether or not it would ever run again, but it is working fine. Thank you for your prompt attention with sending the parts. i dont know if there was a different way to solve this problem, but i felt if there was an expection plate on the side of the unit, it would be helpful.

I just took the bottom front panel off and the parts I needed to rplace where in the back and very easy to get to . I decided to replace all 3 while I was in there. The parts were not to high, so that is why I did that.

Simple,I unplugged the dryer and took off the panel located below the dryer door. To do that unscrewed 2 small screws on the underside of the panel. Once that was off I used a flashlight to locate the heating element which was in the rear of my Amana. Using a socket attached to a screw driver I turned 4 screws out of the element and it was free. I brought the element closer and compared it with the new element and made note of the wire pattern. I plugged in the new wires I received in the box into the new unit and then one by one unhooked the wire leads coming out of the dryer. I reversed the above there it was...maybe 30 minutes!

I took off two screws on the front panel and removed it. I then located the old element inside at the back, left side of the dryer. I removed the two screws holding it in and then transfered the wires to the new element. My dryer works better than it ever did before. Thanks,