Get in touch, we're here to help!
1-866-883-8386
Monday to Saturday
8am - 8pm EST
Product Description
Compressor Overload and Relay Kit Specifications
The start relay briefly boosts the compressor, and then shuts off as soon as the motor gets up to speed. The overload provides added protection for the compressor motor because in addition to protecting against excessive current, it also protects against excessive temperature use.
How Buying OEM Parts Can Save You Time and Money
Troubleshooting
This part fixes the following symptoms:
Will Not Start | Fridge too warm
This part works with the following products:
Refrigerator.
This part works with the following products:
Maytag, Magic Chef, Crosley, Amana.
Part# 12002782 replaces these:
AP4009659, 1194680, 12002782, 61005518
Customer Reviews
Filter By Rating:
- < Prev
- 1
- Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
Roger P - August 6, 2022
Verified Purchase
Part worked as expected
The part came quickly, was easy to install according to the good instructions. The fridge is now working again
- < Prev
- 1
- Next >
Customer Repair Stories
Average Repair Rating: 3.8 / 5.0, 2 reviews.
What's this?
- < Prev
- 1
- Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
Fridge would run but not blow cold air. Compressor would cycle for 12 seconds every 5 minutes
remove back lower panel using nutdriver. Locate and remove Relay and Overload parts from side of Compressor which were located inside a small white box shaped cover unti held on by a spring clip. Attach new Relay and overload to 3 pin terminals on side of compressor. Attach 1 white & 1 orange/white wire to relay terminals. Attach supplied white jumper wire to Overload and other end to Blue wire. Instal new cover supplied with kit replacing old box type cover.
Other Parts Used:
-
Fred from Concord, NH
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver
61 of 89 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Frig wasn't cooling or freezing
ohms-tested the overload relay and PTC component BUT failed to test the compressor. Turns out that it was the compressor was bad and a do-it-ourselfer won't be able to change out this component. Must be licensed to install freon back into the lines once they are separated. Also specialized soldering equip. and freon equipment is needed to perform this task. And if you add too much or the wrong kind of product or don't accurately install the bullet-piercing valve you can risk damaging the unit. So, ALWAYS Oms-test the compressor while testing the capacitor and overload and relay kit!!
Other Parts Used:
-
Bruce from CORRALES, NM
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:Less than 15 mins
-
Tools:Nutdriver, Pliers
1 person
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
- < Prev
- 1
- Next >
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Related Parts
Model Cross Reference
This part works with the following models:
PartSelect Number: PS2004057
Manufacturer Part Number: 12002782
Manufacturer Part Number: 12002782
Brand
Model Number
Description
Get in touch, we're here to help!
1-866-883-8386
Monday to Saturday
8am - 8pm EST