Product Description
SENSOR ASSEMBLY Specifications
This is a replacement sensor assembly for your washer. It may also be known as a motor rotor position sensor. The sensor assembly monitors the direction and speed of the spinning rotor and communicates this information to the electronic control board. If your washer pumps but will not spin or agitate, you may have a damaged sensor assembly. This part is sold individually, and is an OEM part sourced directly from the manufacturer. Be sure to shut off the power to your washer before you begin this repair.
How Buying OEM Parts Can Save You Time and Money
Troubleshooting
This part fixes the following symptoms:
Will not agitate | Spinning Issues | Will Not Start | Spins slowly
This part works with the following products:
Washer, Washer Dryer Combo.
This part works with the following products:
LG, Kenmore.
Part# 6501KW2002B replaces these:
6501KW2002A
Customer Reviews
Filter By Rating:
- < Prev
- 1
- 2
- Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
Murray L - September 29, 2024
Verified Purchase
A perfect replacement part
I had purchased a version of this part via Amazon and it turned out not to fit properly. I wasted several hours trying to reshape the plastic housing to make it fit, but it was a total waste of time.
The PartSelect sensor assembly, on the other hand, was a perfect fit and it took me just a few minutes to snap it into place, reattach the wiring harness and put the motor back together. The washing machine is now working perfectly again.
DOUG S - August 26, 2024
Verified Purchase
Simple to repair a great machine worth the effort
The Sensor arrived as promised, even at the cottage.
Maryke D - April 18, 2024
Verified Purchase
Easy repair works great
It arrived in good time was exactly what I needed to fix my washer. It runs great once again
Donald B - April 21, 2022
Verified Purchase
LG washer repair
The right part came fast, important with 3 kids making laundry just as fast.Easy fix,little down time Thanx
Philippe C - December 7, 2021
Verified Purchase
Solved the problem
This part replaced the original one seamlessly. The LE error code is gone.
Neil R - October 31, 2021
Verified Purchase
Rotor position sensor - Easy repair with the proper tools.
Once you get the stator removed from the washing machine (15-20 minutes), the sensor installs in a snap with a snap. Thanks to Partselect.ca for getting me up and running with their quick delivery.
Michael M - September 1, 2021
Verified Purchase
Did the job, washer working now.
Easy install following how to video. Machine running perfectly now.
Albert B - July 21, 2021
Verified Purchase
easy repair, works great!
washer had LE code, would stop, not go into rinse and spin mode, this rotor sensor cured my problem, very cost effective fix! A.B.
Alex C - June 2, 2021
Verified Purchase
Easy Repair, Exact part – worked as expected
The part was in factory condition and was delivered next day as promised. The washer is back in working order.
Linda H - May 31, 2021
Verified Purchase
The part came fast - easy repair - and I am a very happy customer!
I am very pleased with the great service. The part came very fast - and easy to track along the way! We used a youtube video to help guide us - and it was an easy install! I was back to washing clothes within an hour. I would highly recommend PartSelect to any one needing a quick and guaranteed DIY repair. Thank you!!
- < Prev
- 1
- 2
- Next >
Customer Repair Stories
Average Repair Rating: 3.6 / 5.0, 7 reviews.
What's this?
- < Prev
- 1
- Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
LE Error Message and won't spin drum properly
I first tested the motor per the service manual. I checked the resistance between the terminals of the 3 pin connector. It's supposed to be 5-15 ohms. The motor checked out so I replaced the main electrical board. It turns out that wasn't the problem. After a brief web search I found out that the hall sensor (which is attached to the motor stator) was the likely cause of the failure. I replaced that and everything works great now. And now I have a spare main board in case that ever fails. I also want to mention that I took the time to remove the dispenser box (where the water comes in and is directed to the different cleaning products) and cleaned it with a very strong bleach solution. It got rid of the mildew and funky smell. It seems that the fabric softener caused a lot of mildew to form inside the dispenser directly above the fabric softener tray. The bleach took care of that. This is probably something that should be done routinely to keep the mildew from forming.
Other Parts Used:
-
Mark from Harrisburg, PA
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Screw drivers, Socket set
239 of 311 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
LE fail code
Removed back of washer with screw driver, Removed outer motor cover with a 17 mm socket (1 bolt), Removed motor stater using 10 mm socket (8 bolts). Left motor plugged in and and tipped to the side exposing the sensor. Unplug and snap off sensor. Reassembled in opposite order. Machine works great. Very easy fix, and perfect fit on part.
Other Parts Used:
-
scott from GODDARD, KS
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Screw drivers, Socket set
25 of 26 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
"Le" Fail Code on digital display ... Washer would not agitate and made an odd noise.
I first thought there was a mechanical problem but after checking everything mechanical I discounted that idea ... I researched and found out from others with a similar problem that the Le code display was probably a sensor problem ... I ordered a replacement sensor ... With the new sensor available, I removed the access panel to the back of the machine (phillips head screw driver - 4 screws) ... Remove the exposed motor half (1 bolt - 17mm scocket) ... Loosen the motor stator that has the wired coils (10mm socket - 6 bolts) ... Hold motor unit to the side without disconnecting the wiring harness ... Disconnect the sensor wire connector and remove the old sensor ... Clip the new sensor in place (same position as the old one) and re-connect ... Reverse the assembly procedures ... This fixed the problem and the washing machine works like a new one ... The wife is HAPPY!
Other Parts Used:
-
Ronny from GASTONIA, NC
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Screw drivers, Socket set
20 of 25 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Code LE
Disconnected power supply and water supply hoses. Laid machine on its back because this is a top load machine. Removed one bolt to take off stator then 6 bolts to remove rotor. Put it on side without taking off wire assembly. Snapped off rotor position sensor and installed new one. Put all back together and connected power supply and new stainless braided hoses. WORKS PERFECT. Thanks !
Other Parts Used:
-
Ronald from BELLE CHASSE, LA
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Screw drivers, Socket set
9 of 10 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Kept getting an LE code and washer would stop.
Disconnect elec., hot and cold water supply and drain hose. Lay washer on it's back. Removed nut from center housing. Removed screws from stater. Disconnected wires with flat screw driver at sensor and stater. Installes new sensor. Put everything back together. Washer works great. No LE code.
Other Parts Used:
-
Chris from NEW CUMBERLND, PA
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Screw drivers, Wrench (Adjustable)
7 of 8 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The washer drum would not spin around completely. It would just jerk and try to spin. Error code LE showed up.
We followed the installation video step by step that was found on another website.
Other Parts Used:
-
Brenda from BROWNSVILLE, KY
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Screw drivers
7 of 10 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
would not spin le code
bought a position sensor
top load machine when i tipped the machine over i found
the nut and washer on the floor .replaced the sensor and nut
took about half an hour
top load machine when i tipped the machine over i found
the nut and washer on the floor .replaced the sensor and nut
took about half an hour
Other Parts Used:
-
gregory from TEWKSBURY, MA
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Screw drivers, Socket set
5 of 6 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
- < Prev
- 1
- Next >
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
- < Prev
- 1
- Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Lina
September 23, 2023
What i should do o change for a LG washer "de" Error code
For model number WM3470HVA
Hi Lina, thank you for your inquiry. According to our research, the "dE" error code on your LG washer indicates that the washer door was unable to lock. To fix this error code, we would recommend to turn the machine off by pressing the power button and unplug your machine and restart it again. Next, press and hold the Start/Pause button for 5 seconds. If that does not work, you may need to check the door lock assembly, part number PS3533609, to help fix this issue. We hope this information helps!
2 people found this helpful.
Was this helpful?
Thank you for voting!
Related Parts:
Matthew
April 12, 2023
Please confirm this is the hall stator assembly for my model washing machine.
For model number WM3170CW
Hello Matthew, Thank you for the question. The Sensor for this model is only sold as part of the Washer Motor Stator. The Sensor is not sold on its own. We hope this helps, good luck with the repair!
1 person found this helpful.
Was this helpful?
Thank you for voting!
Related Parts:
Jim
March 23, 2023
Unit does not power on, CB checked, power at the receptacle
For model number WM377OHWA
Hello Jim, thank you for contacting us. Based on the description that you have provided, we would recommend checking the noise filter, part number PS11710201, and the power cord, part number PS12079896. If the issue still occurs, you may need to check the display board, part number PS12080523. We hope this solves your problem!
Was this helpful?
Thank you for voting!
Related Parts:
Randy
April 18, 2023
When coming to the spin cycle, the washer stops and displays the LE code. I’ve tried the “unplug/press and hold start button/replug” reset but still persists.
I’ve been able to finish the spin cycle by restarting and running on speed cycle setting. My research diagnosis would tell me that it’s the Hall sensor at fault. Is this likely correct ? And if so, which part should I be ordering? Thanks!
For model number WM2701H
Hi Randy, thank you for reaching out. An LE error code indicates that the motor is locked, possibly due to a heavy wash load. Since you have already reset the washer, we recommend checking to replace the rotor position sensor switch, part number PS16556422. We hope this solves your issue!
Was this helpful?
Thank you for voting!
Denise
May 4, 2023
Will part #6501kw2002a changed to #6501kw2002B fit my front load lg washer.
For model number WM3370HWA
Hello Denise, thank you for the query. According to our research, the sensor assembly does not come separately. You may need to buy the stator assembly, part number PS3635512. We hope this helps!
Was this helpful?
Thank you for voting!
Related Parts:
- < Prev
- 1
- Next >
Related Parts
Model Cross Reference
This part works with the following models:
PartSelect Number: PS16556422
Manufacturer Part Number: 6501KW2002B
Manufacturer Part Number: 6501KW2002B
Brand
Model Number
Description