The timer controls most of the operations of the washer: water level, tub filling and emptying, length of cycles, and cycle setting sequences.
How Buying OEM Parts Can Save You Time and Money
Troubleshooting
This part works with the following products:
Washer.
This part works with the following products:
Kenmore, Maytag.
Part# WPW10187167 replaces these:
AP6016562, W10187167
Customer Reviews
Average Rating:
★★★★★
★★★★★
2 Reviews
5.0
Filter By Rating:
5 Stars
2
4 Stars
0
3 Stars
0
2 Stars
0
1 Star
0
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
★★★★★
★★★★★
Barbara J - June 25, 2023
Verified Purchase
Great part : worked as expected
Part came very fast. Hardest part was figuring out how to remove console to install. Make sure you are holding the part when you push the knob back on. Machine is back in operation again.
★★★★★
★★★★★
PATTI S - April 25, 2022
Verified Purchase
Fit perfectly, cured the problem all is good
It was the timer, easy to install, did not take long, machine works great, short delivery time
< Prev
1
Next >
Customer Repair Stories
Average Repair Rating: 4.6 / 5.0, 2 reviews.
What's this?
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
Timer would not advance
After looking at the new part and reading how to take off the original timer, it then took me about 15 min to put the new part on the machine. My sister-in-law told me her boyfriend had repaired his washer buy buying the part on line. Sears wanted over three hundred dollars. I got on line and fixed it myself, don't be afraid to try and save a few bucks by doing it yourself, you can always find a how to on line. And I didn't have to wait from 8:00 - 12:00 for the repair man!!!!!
Other Parts Used:
laura from la habra, CA
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
49 of 68 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Timer opened water valve and activated agitator at the same time.
Diagnostic: damaged timer I unplugged and opened the control panel to remove the timer. Once removed, I installed the new timer. I placed the control panel back, plugged back, set the timer, and go! It's working like a brand new washer!
Other Parts Used:
GONZALO from HAINES CITY, FL
Difficulty Level:
Very Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Pliers, Screw drivers, Socket set
1 personfound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
< Prev
1
Next >
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
3 questions answered by our experts.
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Roger
November 13, 2019
Top load Kenmore washer starts to agitate before water fills. Is this most likely a timer problem?
For model number 110.29822800
Hello Roger and thanks for writing.
Usually, when this happens, it is because of the load sense switch. The relay in the switch sticks and allows the washer agitate to before it fills. A simple check is to access the load sense switch and unplugging the wires to it. Then check the operation. We hope this helps. Please contact us at any time
.
If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a technician.
4 people found this helpful.
Was this helpful?
Thank you for voting!
Anthony
January 9, 2020
Washer is not allowing water in the tub. Screens are clean and I have good water pressure
For model number 110.29822800
Hello Anthony, Thank you for the question. I suggest testing the Water Valve. Set your multitester to the R X 1 ohms setting to test for continuity. Place each of the multitester's leads on a terminal. Your multitester should display a reading between 200 and 500 ohms. Closely examine your water inlet valve. The exact ohm resistance rating you should test for may be marked on the valve. We hope this helps!
Fresh Flow Produce Preserver is made for your refrigerator to help keep produce fresh for longer by absorbing the chemical, ethylene, that causes your fruits and vegetables to ripen quicker. Your produce could be fresh f...
Having a problem with a funky-smelling washing machine, or one that just doesnt seem to clean your clothes as well as it used to? Say hello to the Affresh Washing Machine Cleaner by Whirlpool. This powerful washing helpe...
Affresh dishwasher Cleaner is specially formulated to help remove limescale and mineral build-up that can be unsightly and could affect your dishwasher's performance. Each tablet is designed to clean inside your machine ...
Make your cooktop shine with Frigidaire ReadyClean Glass and Ceramic Cleaner. Our scratch-free, streak-free formula removes smudges, grease, burnt-on food, dirt and oil, while protecting and polishing to repel dust and d...
[{"position":0,"name":"Home","title":"Home","url":"/"},{"position":1,"name":"Circuit Board or Touch Pad","title":"Circuit Board or Touch Pad","url":"/Washer-Circuit-Boards-and-Touch-Pads.htm"},{"position":2,"name":"WPW10187167","title":"WPW10187167","url":""}]
