ZPSQ3120T8WW General Electric Washer - Overview
Sections of the ZPSQ3120T8WW
[Viewing 4 of 4]
Keep searches simple, eg. "belt" or "pump".
DAMPENING STRAP 2PACK
PartSelect #: PS18351785
Manufacturer #: WH01X39337
The tub dampening straps support the wash tub and reduce vibration by keeping the tub at the center of the cabinet. If your washer shakes and moves, or is making a loud banging noise during the wash c...
No Longer Available
Agitator Coupling Kit
PartSelect #: PS1517844
Manufacturer #: WH49X10042
This is a washing machine agitator coupling kit. It connects the transmission drive shaft to the agitator base. It includes the couple, gasket, and bolt.
$96.22
Special Order
Selector Knob with Clip
PartSelect #: PS271094
Manufacturer #: WH1X2721
This knob accepts a D-shaped shaft. Sold individually.
No Longer Available
Tub Seal
PartSelect #: PS4704237
Manufacturer #: WH02X10383
The main tub seal is located between the transmission and the outer tub. It's the primary water seal in the outer tub for the transmission-shaft. This seal is difficult to replace and should probably ...
$27.58
Special Order
Dual Action Agitator
PartSelect #: PS1482519
Manufacturer #: WH43X10034
This does not come with the fabric dispenser - must order separately or use original part.
$142.92
Special Order
Timer Knob with Clip
PartSelect #: PS271124
Manufacturer #: WH1X2754
White in color.
No Longer Available
Hub Nut
PartSelect #: PS271505
Manufacturer #: WH2X1193
This part is the hub nut, or lock down nut for your washing machine. It is designed to hold the inner tub on to the transmission. If your hub nut is stripped or damaged, it may need to be replaced. T...
$29.12
Special Order
Split Ring
PartSelect #: PS1766022
Manufacturer #: WH02X10265
This split ring is two inches in diameter.
No Longer Available
Drain Hose
PartSelect #: PS890597
Manufacturer #: WH41X10096
This drain hose is a replacement part for your top-loading washer. The hose measures 57 inches in length.
$79.66
Special Order
Drain Pump and Motor Assembly
PartSelect #: PS8768445
Manufacturer #: WH23X10030
This pump helps expel water from the washing machine and is activated after the spin speed is maintained for a specific period of time.
$137.13
Special Order
Questions And Answers for ZPSQ3120T8WW
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Symptoms of the ZPSQ3120T8WW
[Viewing 17 of 17]Leaking
Fixed by
these parts
these parts
Show All
Will not agitate
Fixed by
these parts
these parts
Show All
Will not drain
Fixed by
these parts
these parts
Show All
Will Not Start
Fixed by
these parts
these parts
Show All
Burning smell
Fixed by
these parts
these parts
Show All
No hot or cold water
Fixed by
these parts
these parts
Show All
Marks left on clothes
Fixed by
these parts
these parts
Show All
Shaking and Moving
Fixed by
these parts
these parts
Show All
Spins slowly
Fixed by
these parts
these parts
Show All
Does not dispense fabric softener or detergent
Fixed by
these parts
these parts
Show All
Noisy
Fixed by
these parts
these parts
Show All
Spinning Issues
Fixed by
these parts
these parts
Show All
Won’t Start
Fixed by
these parts
these parts
Show All
Water Filling Issues
Fixed by
these parts
these parts
Show All
Draining Issues
Fixed by
these parts
these parts
Show All
Touchpad does not respond
Fixed by
these parts
these parts
Show All
Noisy and Marks Left on Clothes
Fixed by
these parts
these parts
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
One of eight clips broke off of the agitator assy allowing the assembly to come lose on heavy loads.
I replaced the coupling by only having to remove one bolt with a socket wrench. Once replaced I installed the new assy over the coupling making sure ro align the splines then pushing down until the assy snapped into place. Easy.
Parts Used:
-
Paul from Carneys Point, NJ
-
Difficulty Level:Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Socket set
680 of 728 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Replaced broken START knob on dryer.
Slid off the old START knob, then pushed on the new START knob.
I created and printed a label on my computer for use with the time selector dial, which must be set at or beyond 10 minutes, before turning the START knob.
I made a label that says "Minimum" with a red arrow that points past the 10 minute setting on the time selector dial.
My teenage daughter was not setting the time selector dial, to a point past 10 minutes. When she turned the START knob, the dryer would not come on, because the time selector dial was not set past the 10 minute setting.
My daughter had continually twisted the START knob until it broke. I am hoping she will be able to see the large printed label I put on the dryer near the time selector, saying "Minimum" with a large red arrow pointing past 10 minutes.
I am very pleased that I was quickly able to find the exact matching START knob for my dryer and the exact same color, from PartSelect.Com
I created and printed a label on my computer for use with the time selector dial, which must be set at or beyond 10 minutes, before turning the START knob.
I made a label that says "Minimum" with a red arrow that points past the 10 minute setting on the time selector dial.
My teenage daughter was not setting the time selector dial, to a point past 10 minutes. When she turned the START knob, the dryer would not come on, because the time selector dial was not set past the 10 minute setting.
My daughter had continually twisted the START knob until it broke. I am hoping she will be able to see the large printed label I put on the dryer near the time selector, saying "Minimum" with a large red arrow pointing past 10 minutes.
I am very pleased that I was quickly able to find the exact matching START knob for my dryer and the exact same color, from PartSelect.Com
Parts Used:
-
SAM from ROCK HILL, NY
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
504 of 515 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The inside of the Selector Knob was stripped
Removed the damaged knob and replaced it with the new knob. Very ease
Parts Used:
-
Frank from Irvine, CA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
383 of 389 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!