This 18 ml bottle of white appliance touch-up paint is used to cover scratches or marks on your appliance. The white touch-up paint can be used on refrigerators, microwaves, ranges, clothes dryers, an...
The point of the lid switch is for the tub to stop spinning when the washer lid is opened. It is a safety precaution just in case someone decides to stick their hand inside the washer while the tub is spinning.
This drive hub kit (part number W10528947VP) is for washers.
Drive hub kit W10528947VP connects the spin basket to the spin shaft that spins the basket. The kit may include multiple parts; refer to...
This is a replacement clutch assembly or cam kit for your washer. The clutch assembly is mounted on the drive shaft on the bottom of your washer. You may need to replace the clutch assembly if the spl...
This part changes the transmission from agitation to spin mode. This actuator is for washers.
Actuator shifts the splutch and monitors the position of the splutch.
The drain hose carries used water from the washer to your house drain.
$31.80
In Stock
Questions And Answers for WTW5800BW0
Ask our experts a question about this model and we'll get back to you as soon as possible!
5 questions answered by our experts.
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Mike
July 29, 2021
The lid lock comes open during mid cycle
For model number WTW5800BW0
Hello Mike, Thank you for the question. With the Lock opening during the cycle it could be defective and need to be replaced, PartSelect Number PS3497627. We hope this helps!
Have a mould smell on all the clothes after washing and drying , Is there a way to clean this up?
For model number WTW5800BW0
Hi Douglas, thank you for contacting us. Scrubbing your washer tub is a great way to deep-clean your washing machine and ensure there’s no soap or detergent scum left behind. Pour a quart of white vinegar into the washer tub with 1 cup of baking soda, and use a stiff nylon brush to scrub the interior. Then run a wash cycle on the hottest temperature and heaviest laundry load settings. You will also need to clean the gasket. Apply vinegar to a paper towel and wipe down the inside of your gasket to kill any buildup that might be causing bad smells. We hope this information is helpful.
1 person found this helpful.
Was this helpful?
Thank you for voting!
Luis
May 29, 2023
Washer is shaking s lot...what can be replace to stop it to shake?
For model number WTW5800BW0
Hi Luis, thank you for reaching out. Based on our understanding of the issue, we would suggest that you make sure the load is balanced inside the tub and that the unit is balanced. If that is not causing the issue, then you may need to check the suspension rods, part number PS11703287, as they are most likely faulty and may need to be replaced. We hope this helps!
There is a blue plug inside of softener cup that broke. When you add softener it leaks onto clothes.
For model number WTW5800BW0
Hello Ramona, thank you for reaching out. The blue plug does not come separately; we suggest you replace the washer dispenser drawer, part number PS11757009. We hope this information helps!
A detailed Service Technician Service Manual is hidden inside the machine on the front panel. It is hidden by the bleach dispenser input. It gives a list of fault codes and instructions for calibration after repair, resetting fault codes, and a manual test mode for stepping the machine through each mode on command. The Tachometer failed which would not let the machine come up to maximum spin speed. The tachometer is part of the solenoid actuator that shifts the transmission. It is not specifically called out in the manual. Any failure causes the lid lock light to blink which gives the appearance of a lid lock failure
The instructions that came with the part were worthless. Essentially, unplug, put in new part, plug it back in. I spent a considerable amount of time on the internet and finally found a video showing how to open the top. Unlike other models, it is held down by clamps in the back rather than clips in the front. Once finding this information the installation was simple. Remove the clamps and the back of the console, slide the top forward and lift, remove and replace the lock and reassemble. You don't even have to remove the hoses.
Well, first investigated and found loose nut on drive clutch. First take off the two screws with nut drive then cover off using a screwdriver blade to snap off the cover. Then socket ratchet to take off the nut on drive clutch. take off belt by slowly rotating the drive gear. two screws that hold the electronics to the upper drive clutch and put aside, so you can snap off the cover for drive clutch on upper part with screwdriver and off the parts come and install whole unit back as took it apart. Line up the new upper clutch so that is position as was before. (Using parts diagram helps a lot as www. partsselect.com has for you or Maytag.com.) Then put the electronic part board back on and the gear and nut. Make sure it is tight by several attempts to make sure it's snugged up good and then slowly roll belt back on the pulley and motor drive. Put your cover guard back on with two screws and done.
