WSM2780TBWAB General Electric Washer Dryer Combo - Overview
Sections of the WSM2780TBWAB
[Viewing 6 of 6]
Keep searches simple, eg. "belt" or "pump".
Dishwasher Hose Clamp Kit
PartSelect #: PS270806
Manufacturer #: WH1X2036
This hose clamp kit contains two clamps. The smaller of the two is an inch in diameter while the larger of the two is two inches in diameter.
$22.95
Special Order
Water Inlet Valve
PartSelect #: PS270303
Manufacturer #: WH13X78
This water inlet valve attaches the water lines to the back of your appliance. The attaching solenoids on the valve open and close according to the desired temperature, or amount of water needed.
$101.92
Special Order
Top Drum Glide Kit
PartSelect #: PS264864
Manufacturer #: WE03X10001
This top drum glide kit comes with the adhesive.
$186.91
Special Order
Washer Timer
PartSelect #: PS269959
Manufacturer #: WH12X1040
The timer controls most of the operations of the washer: water level, tub filling and emptying, length of cycles, and cycle setting sequences.
No Longer Available
Questions And Answers for WSM2780TBWAB
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Symptoms of the WSM2780TBWAB
[Viewing 4 of 4]Noisy
Fixed by
these parts
these parts
Show All
Leaking
Fixed by
these parts
these parts
Show All
Marks left on clothes
Fixed by
these parts
these parts
Show All
Will not agitate
Fixed by
these parts
these parts
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Clothes were getting stuck in the outer rim of the dryer.
Turns out the part was only $50, and the repair was easy as can be...
1. Pop the top cover off, pressing the clips down with a flathead screwdriver.
2. Remove the two screws that hold the front cover in place, and take the cover off.
3. Remove the old glides and the felt they're attached to.
4. Scrape off any remains of the felt and glue.
5. Apply the glue they send with the part. Give it a minute to get tacky before you stick the new part on.
6. Stick the new part on. Let it sit for a few hours before re-assembling the dryer.
Thanks, PartSelect, for saving me a bunch of money, yet again!
1. Pop the top cover off, pressing the clips down with a flathead screwdriver.
2. Remove the two screws that hold the front cover in place, and take the cover off.
3. Remove the old glides and the felt they're attached to.
4. Scrape off any remains of the felt and glue.
5. Apply the glue they send with the part. Give it a minute to get tacky before you stick the new part on.
6. Stick the new part on. Let it sit for a few hours before re-assembling the dryer.
Thanks, PartSelect, for saving me a bunch of money, yet again!
Parts Used:
-
Joseph from Delaware, OH
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
5 of 5 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Dryer kept eating clothes! They'd catch between the door panel and drum.
*****I HIGHLY RECOMMEND buying both bottom felt and top felt with glides and replacing them as a pair. Do it now!!****
First I removed the screws on the top of the control panel and lifted the control panel free. Next I pried the top cover off the drier. Reaching down inside the drier, I removed 2 screws holding the front panel in place (one on each side of the drum, screw heads are INSIDE the appliance) Then the front panel popped off toward the front, leaving the drum dangling inside the cabinet. I removed the old top felt and glides one piece) which had nothing left to them. I used a rag soaked with Acetone and a putty knife to remove the old adhesive and clean the mating surface. Following the supplied instructions (that came with the part) I glued the new piece in place. I reassembled the dryer and tested it out - I recommend giving all internal air ducts a good vacuuming while the dryer is apart - and everything seemed OK for a week. Then another article of clothing fell prey to the dryer, becoming lodged between the drum and front panel again. I suspect the culprit is the space BELOW the drum where the bottom felt is worn much more than the brand new felt just installed. I HIGHLY RECOMMEND buying both bottom felt and top felt with glides and replacing them as a pair.
First I removed the screws on the top of the control panel and lifted the control panel free. Next I pried the top cover off the drier. Reaching down inside the drier, I removed 2 screws holding the front panel in place (one on each side of the drum, screw heads are INSIDE the appliance) Then the front panel popped off toward the front, leaving the drum dangling inside the cabinet. I removed the old top felt and glides one piece) which had nothing left to them. I used a rag soaked with Acetone and a putty knife to remove the old adhesive and clean the mating surface. Following the supplied instructions (that came with the part) I glued the new piece in place. I reassembled the dryer and tested it out - I recommend giving all internal air ducts a good vacuuming while the dryer is apart - and everything seemed OK for a week. Then another article of clothing fell prey to the dryer, becoming lodged between the drum and front panel again. I suspect the culprit is the space BELOW the drum where the bottom felt is worn much more than the brand new felt just installed. I HIGHLY RECOMMEND buying both bottom felt and top felt with glides and replacing them as a pair.
Parts Used:
-
Joshua from Bristol, RI
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Screw drivers
3 of 3 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Dryer stopped working
What a mess. Partselect shipped the wrong part. I paid a technician to fix it, only to learn the part was wrong. I order the right part. I needed to send it back, reorder the same part, and pay for a second visit from the technician. The nice people at partselect gave me a $7 credit for costing me $200. Losers
Parts Used:
-
Shanice from RESTON, VA
-
Difficulty Level:Very Difficult
-
Total Repair Time:More than 2 hours
3 of 3 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!