WSM2700HFWWW General Electric Washer Dryer Combo - Overview
Sections of the WSM2700HFWWW
[Viewing 6 of 6]
Manuals & Care Guides for WSM2700HFWWW
Click to downloadKeep searches simple, eg. "belt" or "pump".
Lower Front Felt Seal with Adhesive
PartSelect #: PS832645
Manufacturer #: 5303937183
$36.73
In Stock
Timer Knob - Dryer
PartSelect #: PS755794
Manufacturer #: WE01X10160
Used with washer/dryer combo machines. This knob takes a D-shaped shaft.
$101.82
Special Order
Rear Bearing
PartSelect #: PS267858
Manufacturer #: WE3X70
Bearing Only. This part helps your appliance run as quietly as possible.
$59.10
Special Order
DRYER LINT FILTER
PartSelect #: PS12741280
Manufacturer #: WE16X29397
This is the replacement lint filter for your dryer. The lint filter traps unwanted lint and debris so your dryer can effectively dry your clothes.
No Longer Available
Upper Felt Seal with Adhesive
PartSelect #: PS652857
Manufacturer #: WE09X10013
Has your dryer been making strange noises or not running as efficiently as it used to? It could be an issue with the Dryer Felt Seal. This genuine GE replacement part ensures your dryer drum glides sm...
$82.95
Special Order
Rear Bearing Shaft Support
PartSelect #: PS265828
Manufacturer #: WE13X10011
Are you tired of your dryer not functioning as it used to? Your stress ends here with our GE Dryer Drum Bearing. This is more than just a spare part - it's an essential component that brings your drye...
No Longer Available
Drain Pump
PartSelect #: PS3502779
Manufacturer #: WH23X10041
This pump helps expel water from the washing machine and is activated after the spin speed is maintained for a specific period of time.
$188.34
Special Order
Control Thermostat
PartSelect #: PS265265
Manufacturer #: WE04X10028
This thermostat controls the internal drying temperature.
Cycling themostats continually cycle the heating element off and on to maintain a constant inner temperature. This particular cycling thermos...
$91.43
Special Order
Thermal Limiter
PartSelect #: PS755806
Manufacturer #: WE04X10094
This part is found in the same location as the Terminal Block at the back of the Dryer. It acts as a safety device which prevents your appliance from overheating.
$101.19
Special Order
Questions And Answers for WSM2700HFWWW
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
- < Prev
- 1
- Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Keith
November 23, 2022
My dryer is kicking on but will not move spin nothing
For model number WSM2700HFWWW
Hello Keith, thank you for reaching out. We have researched your model and would recommend checking the following parts to fix your issue: Drum Belt, part number PS959964, Bearing Shaft Support, part number PS265828, motor, part number PS12722938. Customer service is available 7 days a week if you need help placing an order. Glad to be of assistance!
1 person found this helpful.
Was this helpful?
Thank you for voting!
Related Parts:
Rear Bearing Shaft Support
No Longer Available
Drum Belt
$140.29
Special Order
Leyla
January 20, 2020
I need the timer washer
For model number WSM2700HFWWW
Hello Leyla, Thank you for contacting us. I have researched the model you have provided and have found the part you are looking for is PartSelect Number PS2370735. we hope this helps.
Was this helpful?
Thank you for voting!
Michelle
February 4, 2020
When the washer on this laundry unit first starts into the spin cycle, it makes a loud grinding noise or hum and then it quiets down. Can you tell me what part needs to be replaced?
For model number WSM2700HFWWW
Hello Michelle, Thank you for the question. We suggest checking for damage or wear to the Trunnion, Bearing, Snubber Ring and the Tub Seal Kit. Please see the related parts. We hope this helps.
Was this helpful?
Thank you for voting!
Related Parts:
SNUBBER RING
No Longer Available
BEARING
No Longer Available
Kathy
March 3, 2024
Dryer doesn't heat up but drum will turn
For model number WSM2700HFWWW
Hi Kathy, thank you for contacting us. We have found that the issue is with the cycling thermostat, part number PS265265. It monitors and regulates the temperature inside the dryer. You may need to replace the thermostat to fix the issue. We hope this sorts out your problem!
Was this helpful?
Thank you for voting!
Related Parts:
Control Thermostat
$91.43
Special Order
- < Prev
- 1
- Next >
Common Symptoms of the WSM2700HFWWW
[Viewing 5 of 5]Noisy
Fixed by
these parts
these parts
Show All
Marks left on clothes
Fixed by
these parts
these parts
Show All
Will not agitate
Fixed by
these parts
these parts
Show All
Will not drain
Fixed by
these parts
these parts
Show All
Leaking
Fixed by
these parts
these parts
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Washer would not drain
Removed 2 Hose clamps with pliers. Unplug power source from drain pump. Unscrew 2 mounting screws with 5/16" nut-driver then replace unit in reverse sequence...... Very simple.
Parts Used:
-
Jack from Canyon Lake, TX
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Pliers
29 of 43 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
filter had a hole
-
Patricia from chicago, IL
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
14 of 17 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Felt around drum holder worn and torn.
1. Removed face of dryer (drum 'holder')
2. Disconnected door switch wires
3. Tore off existing felt
NOTE: The length of the felt that I recieved from PartSelect was incorrect (too short). Since the existing felt was worn and torn at the top, I replaced only a length that matched the length of the new felt.
4. Used a razor blade-type gasket remover/scraper to remove the exisitng glue
5. Applied new glue (which comes with the felt) onto the felt and let it set up
NOTE: In hindsite, I would apply the glue to the drum holder instead, as the glue otherwise soaks into the felt. If applied to the drum holder instead, the glue will spread out and provide more surface area for adherence.
6. Installed the new felt, starting at one end and working my way around to the other end, being careful not to stretch it
7. Trimmed the remainder of the existing felt (see first NOTE)
8. Scraped the drum holder below the pulled away ends of the exisitng felt
9. Applied glue to the existing felt, including the trrimmed ends so that the ends do not pull away from the ends of the new felt
10. Re-attached the existing felt
11. Let the glue set-up overnight
12. Reinstalled the face of the dryer, turning the drum so that the felt will not get pushed away
13. Reconnected the door switch wires
14. Turned dryer on, with lid still raised, to check for any drifting of the felt
15. Once assured that the felt would stay in place, put the dryer in service
NOTE: I replaced the felt becasue of the gap that opened due to compression of the felt. The gap, as well as a torn piece of the felt that entered the interior of the drum, was catching clothes and tearing them as they were rotated between the drum and the drum holder. The new felt eliminated this problem.
2. Disconnected door switch wires
3. Tore off existing felt
NOTE: The length of the felt that I recieved from PartSelect was incorrect (too short). Since the existing felt was worn and torn at the top, I replaced only a length that matched the length of the new felt.
4. Used a razor blade-type gasket remover/scraper to remove the exisitng glue
5. Applied new glue (which comes with the felt) onto the felt and let it set up
NOTE: In hindsite, I would apply the glue to the drum holder instead, as the glue otherwise soaks into the felt. If applied to the drum holder instead, the glue will spread out and provide more surface area for adherence.
6. Installed the new felt, starting at one end and working my way around to the other end, being careful not to stretch it
7. Trimmed the remainder of the existing felt (see first NOTE)
8. Scraped the drum holder below the pulled away ends of the exisitng felt
9. Applied glue to the existing felt, including the trrimmed ends so that the ends do not pull away from the ends of the new felt
10. Re-attached the existing felt
11. Let the glue set-up overnight
12. Reinstalled the face of the dryer, turning the drum so that the felt will not get pushed away
13. Reconnected the door switch wires
14. Turned dryer on, with lid still raised, to check for any drifting of the felt
15. Once assured that the felt would stay in place, put the dryer in service
NOTE: I replaced the felt becasue of the gap that opened due to compression of the felt. The gap, as well as a torn piece of the felt that entered the interior of the drum, was catching clothes and tearing them as they were rotated between the drum and the drum holder. The new felt eliminated this problem.
Parts Used:
-
Robert from York, PA
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
10 of 12 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!