This light switch may also be known as a refrigerator door switch or a light switch kit, and is compatible with your refrigerator. The function of the refrigerator door switch is to turn on the light ...
$38.96
In Stock
Order within the next 3 hrs and your part ships today!
Need a new shelf bin for your fridge door? This clear bin fits select Whirlpool, Kenmore, and Maytag models and snaps right into place—no tools needed. It’s made from strong, food-safe plastic and is ...
$43.07
In Stock
Order within the next 3 hrs and your part ships today!
This mounting screw is a genuine OEM replacement part for the door handle in your refrigerator. If you are having trouble shutting the refrigerator door, or opening it, replacing this screw can help s...
$16.12
In Stock
Order within the next 3 hrs and your part ships today!
If your refrigerator or freezer is too warm, or making noises, you may need to replace the fan blade. The fan blade attaches to the evaporator motor, which is in the freezer section, to help circulate...
$47.08
In Stock
Order within the next 3 hrs and your part ships today!
This refrigerator ice maker assembly is a genuine OEM component designed for automatic ice production and dispensing in select models. It includes both the ice mold and control device, working togethe...
$119.90
In Stock
Order within the next 3 hrs and your part ships today!
Experience the simple solution to a wobbly refrigerator with the Whirlpool Refrigerator Leveling Leg. This authentic, factory-made part is designed to keep your refrigerator stable and even, saving yo...
$14.74
In Stock
Order within the next 3 hrs and your part ships today!
I knew the chances of all the freon leaking out was unlikely so I looked at the wiring to the compressor and there was a capacitor and a starter/overload so i figured I would start there. I went on line and found the parts at this site and they were less than the minimum service call charge for a service tech so I figured what the heck let's give her a shot so I did give it a shot. I ordered the parts and they were there in less time than a service tech could come out and i installed the parts and guess what for 90.00 in parts and 15 minutes in time I repaired my refrigerator. Thanks guys, It took less time to order the parts than it did to make the repair so thanks, your website rocks and is very well designed so my hat is off to you guys!
I used a flat screwdriver and released the lock tab on the bottom of the light switch, and pried the switch out, being careful to not damage the plastic around the mounting place of the switch, unplugged wiring from old switch, plugged in the new one and pushed the new switch into place. Job finished light switch now working.
I turned the water and electricity off for the refrigerator. (not sure if this is necessary but is safer) Remove the ice bucket. Cover the Ice auger with a hand towel to catch any screws which my get dropped. Remove four Philips screws holding plastic cover to inside of the door. there are no clip/snaps to worry about but on/off switch needs to be un plugged. Remove cover. Remove two nut head screws holding old ice maker. Remove wiring harness from ice maker and lift ice maker up and out. There are two tabs on the door. Unplug the wiring harness from the ice maker..
Installation: Press the wiring harness into clips on the new ice maker. Install ice maker onto door insuring it is over the tabs on door and the holes for nut screws line up. Plugging the wiring harness in and install two screws.
Plug on/off wiring onto switch and press plastic cover onto inside of door. Take care that it fits inside of rubber door seal. Install four philips screws. Remove hand towel and install ice bucket making sure the ice maker is switched on. Close door. Turn on water and electricity.
This took me 25 min. and I am sure would go faster if I had had instructions.
My refrigerator took awhile before it started to make cubes but has been working like new ever since. This task is easy go for it.
