WPSQ4160T7AA General Electric Washer - Overview
Sections of the WPSQ4160T7AA
[Viewing 4 of 4]
Keep searches simple, eg. "belt" or "pump".
Split Ring
PartSelect #: PS1766022
Manufacturer #: WH02X10265
This split ring is two inches in diameter.
No Longer Available
Inner Tub Base Hub
PartSelect #: PS273296
Manufacturer #: WH45X10027
This part is the replacement inner tub base hub for your washer. It is made of metal and is approximately 15 inches in diameter. The inner tub base hub fits between the wash tub and the spin basket, a...
$115.05
Special Order
Socket Rod Support - White
PartSelect #: PS268394
Manufacturer #: WH01X10001
This part is a replacement socket rod support for your washer. The socket rod support is found at the top of the washer frame in the front part of the washer. It supports the suspension rod, so the ro...
$17.70
Special Order
Dishwasher Hose Clamp Kit
PartSelect #: PS270806
Manufacturer #: WH1X2036
This hose clamp kit contains two clamps. The smaller of the two is an inch in diameter while the larger of the two is two inches in diameter.
$22.95
Special Order
Screw - Black
PartSelect #: PS268950
Manufacturer #: WH02X10002
This screw is sold individually.
$13.95
Special Order
Flood Gasket
PartSelect #: PS271102
Manufacturer #: WH1X2729
This part is for the hose to outer tub.
$46.95
Special Order
Lid Switch Assembly
PartSelect #: PS269962
Manufacturer #: WH12X1043
The pin on the lid pushes on the lever of the lid switch to tell the machine that the lid is closed.
No Longer Available
Water Level Pressure Switch
PartSelect #: PS269794
Manufacturer #: WH12X10069
This part is located behind the control panel. It helps determine the level of water in the washer. As the water fills the hose, while tub is filling, it will push the air against a diaphragm inside t...
$197.32
Special Order
Questions And Answers for WPSQ4160T7AA
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Symptoms of the WPSQ4160T7AA
[Viewing 3 of 3]Leaking
Fixed by
these parts
these parts
Show All
Will not agitate
Fixed by
these parts
these parts
Show All
Noisy and Marks Left on Clothes
Fixed by
these parts
these parts
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Lid switch failed
First removed front washer access panel.
Next: removed top panel torx screws and disconnected lid switch wiring connector
Next: removed washer top/lid
Next: removed inoperative lid switch (two phillips head screws)
Next: installed new lid switch and screws
Next: installed washer top and connected lid switch wire connector
Next: installed control panel and screws
Next: tested installation
Next: installed front washer access panel
Easy repair. FYI, Parts Select had best price and part arrived within two days of ordering! Highly recommend them for your parts.
Next: removed top panel torx screws and disconnected lid switch wiring connector
Next: removed washer top/lid
Next: removed inoperative lid switch (two phillips head screws)
Next: installed new lid switch and screws
Next: installed washer top and connected lid switch wire connector
Next: installed control panel and screws
Next: tested installation
Next: installed front washer access panel
Easy repair. FYI, Parts Select had best price and part arrived within two days of ordering! Highly recommend them for your parts.
Parts Used:
-
Stephen from Woodbridge, VA
-
Difficulty Level:Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
35 of 47 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Pressure switch would not detect water level.
I replaced the pressure switch which I ordered from A-1. It still did not work. I then took a small rigid wire and inserted it into the pressure box on the side of the tub. Then I squirted water thru the tube to clean out the hole where the tube from the pressure switch is hooked up. The washer then worked fine. The pressure switch I replaced was probably OK. This was a learning experiance which cost me $68.00. Still cheaper than a repairman
Parts Used:
-
Dennis from Burley, ID
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
18 of 20 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Loud bang during spinning
Remove aggitator, disconect 4 support straps, pry off clips/ latches on top of drum. Remove small bolt that holds on the small plastic unit unto trans.
That will give you access to the large bolt that holds the hub in place. This nut is on tight use a pipe wrench and adjustable wrench and TURN CLOCKWISE TO REMOVE - lock for direction on nut.
Remove the bin gently and turn over to remove the small bolts that hold the hub in place.
Installation is reverse of removal.
That will give you access to the large bolt that holds the hub in place. This nut is on tight use a pipe wrench and adjustable wrench and TURN CLOCKWISE TO REMOVE - lock for direction on nut.
Remove the bin gently and turn over to remove the small bolts that hold the hub in place.
Installation is reverse of removal.
Parts Used:
-
Jim from Marion, MA
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:1- 2 hours
-
Tools:Pliers, Screw drivers, Wrench (Adjustable)
16 of 18 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!