This 18 ml bottle of white appliance touch-up paint is used to cover scratches or marks on your appliance. The white touch-up paint can be used on refrigerators, microwaves, ranges, clothes dryers, an...
$15.95
In Stock
Order within the next 24 mins and your part ships today!
This part is the replacement halogen light bulb for your range. The bulb is 10 watts and 12 volts. The halogen lamp lights up the inside of the oven you can see the cooktop more effectively in darknes...
$34.44
In Stock
Order within the next 24 mins and your part ships today!
Having issues with your Whirlpool microwave? It might be the Inlet Cover. This small part plays a big role and shields the waveguide channel in your microwave from debris and food splatters. Keeping i...
$64.85
In Stock
Order within the next 24 mins and your part ships today!
Are you tired of unevenly heated meals from your microwave? The Whirlpool Turntable Motor is the solution you need. This genuine OEM part is crucial for your microwave's performance, with its main rol...
$139.09
In Stock
Order within the next 24 mins and your part ships today!
This small but important switch helps keep your microwave safe by making sure it won’t run unless the door is properly closed. It tells the microwave’s control system whether the door is open or shut,...
$57.15
In Stock
Order within the next 24 mins and your part ships today!
If your oven isn’t heating properly or seems to be getting too hot, the high-limit thermostat might be the issue. This part helps keep things safe by shutting off the heat if the temperature gets too ...
$154.02
In Stock
Order within the next 24 mins and your part ships today!
This roller is located underneath the glass turntable. With the help of the motor, this roller helps to rotate the glass tray. This part takes the place of the coupling.
$78.64
In Stock
Order within the next 24 mins and your part ships today!
Have you got a Whirlpool oven, stove, or range that isn't broiling like it used to? Here's something that could help you get back your kitchen groove- the Broil Element by Whirlpool. This part isn't j...
$139.91
In Stock
Order within the next 24 mins and your part ships today!
This product comes in a bottle with a brush like Liquid Paper. It goes on incredibly easy. A second coat might be needed. I wanted to prevent rust from setting in so I covered the scratches and dings. The paint is a little brighter since my washer is 10 years old but it still looks great.
I used a Google search to show how to access the area behind the front panel. There was a folded paper copy with a schematic and wiring diagram in that space.Then I used a multi-meter to determine which of the THREE micro-switches was causing the problem. I called your help line and ordered a replacement switch. The switch was delayed in transit so your agent credited me with the cost of shipping.
When the part arrived, it had three terminals instead of two as shown in the on-line picture but that did not cause any difficulty in using it. It took about 20 minutes to remove and replace the old switch.
All seems to be working well now.
Finding which of the THREE switches was the problem was the most difficult part of the repair. All three "clicked" but the defective one did not click as easily. It needed to be depressed more than the door latch can would provide. Old age?
IMPORTANT: DO NOT TOUCH THE REPLACEMENT LAMP WITHOUT WEARING CLEAN GLOVES. FILM OR FINGER PRINTS ON THE LAMP GLASS WILL CAUSE PREMATURE FAILURE OF THE LAMP.
Remove the 4 screws on right and left mounting rails that hold the unit to the kitchen cabinet. Remove the oven door Remove the chrome oven vent strip below the oven door. This allows a pry point beneath the combo microwave oven assembly to lift up the unit while pulling it out. (Assembly weighs 250 pounds) Pull the unit out from the cabinet housing about 2-3 inches to reveal the right and left sides and the 4 screws holding the the control panel. Remove the 4 control panel screws and pull off the face of the control panel Remove the 2 harness connectors and the ground wire holding the control panel to the unit. Unclip the circuit board above the lamp connector and slide it back out of the way. The lamp is now accessible. Remove the lamp spring holding the lamp to the cabinet. Remove the old lamp Install the new lamp using clean gloves Reassemble in reverse order.
