This hot water inlet valve is designed to regulate water flow into the washing machine during operation. Featuring a standard hose fitting inlet and a single water outlet, it opens as needed to allow ...
$78.09
In Stock
Order within the next 12 hrs and your part ships today!
This valve is used for cold water, bleach dispenser and prewash cycles. It has a standard hose fitting inlet with 2 outlets facing 45 degrees to the right and one outlet facing 45 degrees to the left.
$111.68
In Stock
Order within the next 12 hrs and your part ships today!
This washer hose with bellows, also known as a dispenser hose, is a genuine OEM replacement part for your washer. Replacing this part can be helpful if your washer is leaking. The dispenser hose conne...
$63.78
In Stock
Order within the next 12 hrs and your part ships today!
This washer sensor assembly, also known as a motor rotor position sensor, is a genuine OEM replacement part designed to monitor the direction and speed of the rotor during operation. By communicating ...
$80.21
In Stock
Order within the next 12 hrs and your part ships today!
This friction damper assembly is designed to stabilize the washer tub during operation, particularly during high-speed spin cycles. By absorbing movement and reducing vibrations, it helps ensure quiet...
$66.58
In Stock
Order within the next 12 hrs and your part ships today!
This door boot seal is for front loading washing machines. This part forms a seal between the wash tub and the door, preventing leaks. We recommend unplugging the washer before installing this part an...
$234.78
In Stock
Order within the next 12 hrs and your part ships today!
The blue plastic detergent dispenser holds the detergent and then dispenses it into the washer during the wash cycle. If the detergent dispenser is broken, lost, or if the detergent is not dispensed d...
$36.85
In Stock
Order within the next 12 hrs and your part ships today!
This part is the replacement rear tub gasket for your washer. It is made of black plastic and is approximately 3-1/4 inches in diameter. The rear tub gasket forms a watertight seal between the rear tu...
$56.87
In Stock
Order within the next 12 hrs and your part ships today!
Order within the next 12 hrs and your part ships today!
Questions And Answers for WM3570HWA
Ask our experts a question about this model and we'll get back to you as soon as possible!
2 questions answered by our experts.
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
ROBERT
October 16, 2022
WHEN GOES INTO SPIN CYCLE GOES TO ERROR
For model number WM3570HWA
Hi Robert, thank you for your question. We have researched your model and found that this issue is commonly caused by an unbalanced load. Check if the load is properly distributed. If that does not help, try changing the control board, part number PS11710881. Please reach out to customer service if you need help placing an order. Glad to be of help!
I need the part number for the plastic magnet with spring that attaches to the bottom of the washer door
For model number WM3570HWA
Hello Lincoln, thank you for your question. We found the little plastic part. Door lock spring holder PS11771532 secures the lock spring inside the door latch. However, we did not find a part number of a spring. We hope this information will help you.
I first tested the motor per the service manual. I checked the resistance between the terminals of the 3 pin connector. It's supposed to be 5-15 ohms. The motor checked out so I replaced the main electrical board. It turns out that wasn't the problem. After a brief web search I found out that the hall sensor (which is attached to the motor stator) was the likely cause of the failure. I replaced that and everything works great now. And now I have a spare main board in case that ever fails. I also want to mention that I took the time to remove the dispenser box (where the water comes in and is directed to the different cleaning products) and cleaned it with a very strong bleach solution. It got rid of the mildew and funky smell. It seems that the fabric softener caused a lot of mildew to form inside the dispenser directly above the fabric softener tray. The bleach took care of that. This is probably something that should be done routinely to keep the mildew from forming.
Pull washer away from wall. Unplug cord and remove drain hose from receptacle. Remove 4 screws holding panel to rear of washer. Squeeze and slide back hose clamps on each end of drain hose and loosen center clamp with screwdriver. Remove old hose. Reinstall new hose in reverse order using existing clamps. Re-install back panel.
