The drain pump and motor assembly may also be known as the washer drain pump and is a part for your washer. The drain pump helps expel water from the washing machine. The drain pump is activated after...
$160.58
In Stock
Order within the next 3 hrs and your part ships today!
This hot water inlet valve is designed to regulate water flow into the washing machine during operation. Featuring a standard hose fitting inlet and a single water outlet, it opens as needed to allow ...
$78.09
In Stock
Order within the next 3 hrs and your part ships today!
This washer hose with bellows, also known as a dispenser hose, is a genuine OEM replacement part for your washer. Replacing this part can be helpful if your washer is leaking. The dispenser hose conne...
$63.78
In Stock
Order within the next 3 hrs and your part ships today!
This washer sensor assembly, also known as a motor rotor position sensor, is a genuine OEM replacement part designed to monitor the direction and speed of the rotor during operation. By communicating ...
$80.21
In Stock
Order within the next 3 hrs and your part ships today!
Also known as a door boot seal or bellow and comes with a drain hole. Door boot 4986ER0004F is an original equipment manufacturer (OEM) part that fits some front-load washers in these series: Kenmore ...
$202.07
In Stock
Order within the next 3 hrs and your part ships today!
The magnetic door plunger attaches to the inner door panel of your washer and will hold the door open when the washer is not in use and allows the door and tub seal to dry. By doing this it will preve...
$78.50
In Stock
Order within the next 3 hrs and your part ships today!
This door lock assembly is a critical component in compatible washing machines, responsible for confirming that the door is securely closed before initiating a wash cycle. When functioning properly, i...
$108.57
In Stock
Order within the next 3 hrs and your part ships today!
If your washer isn’t filling properly or skipping parts of the cycle, this water valve might be the issue. It controls cold water flow for the bleach dispenser and prewash cycles. The valve connects w...
$172.14
In Stock
Order within the next 3 hrs and your part ships today!
This round rubber tub seal is designed to prevent water leakage between the front and rear halves of the outer tub in select washing machines. Positioned at the junction of the tub components, it comp...
$43.85
In Stock
Order within the next 3 hrs and your part ships today!
Questions And Answers for WM2140CW
Ask our experts a question about this model and we'll get back to you as soon as possible!
5 questions answered by our experts.
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Mike
May 25, 2023
Overnight the tub will partially fill with water
For model number WM2140CW
Hello Mike, thank you for the question. According to our research, the issue is most probably with the water pressure switch, part number PS3529317. You may also need to check the hot and cold water inlet valves to make sure they are working properly. We hope this helps!
Hi my washer leaves soap residue on clothes even after rinsing 2or3times please help
For model number WM2140CW
Hi Wayne, thank you for reaching out. First, you may need to make sure that you are not using too much detergent. Using too much detergent per load, especially if the water is not hot enough for it to dissolve, can cause a white residue. Also, make sure that the drain hose is clear. If that is not causing the issue, then you may need to check the drain pump, part number PS3579318, as it is most likely clogged. We hope this information helps!
With clothes in washer i keep getting le code. I've removed clothes, turned the power off, unplugged and held the pause button for five seconds. I can then do a drain and spin cycle, minus clothes and it work. Will the rotary position sensor assembly fix this?
For model number WM2140CW
Good Day Leigh. Thank you for your question in regards to your unit (Model Number WM2140CW). Based on our research, an IE error code is for a WM2140CW a water inlet error (indicating that the machine is not getting enough water). This may be an indication that the Water Inlet Valve - Hot (PartSelect Number PS3527427) or the Water Inlet Valve - Cold (PartSelect Number PS11728995) need to be replaced. We hope this helps! Best Regards.
Hello Bruce, thank you for contacting us. The issue could be due to the rear tub basket, part number PS3522855, being worn out and needing to be replaced. Also, make sure the pump turns freely. Small clothing items and lint get stuck in the pump. If the impeller of the pump, part number PS3579318, can not move, then the motor will get hot causing a burning smell. We hope this solves your problem!
I need a new rubber seal for the cap on the pump filter cap assembly Is this available separately or does it only come as a complete piece? And if seal is available price and in stock? If not complete filter assembly w/attached cap with seal installed? And price and availability? Thanks ??
For model number WM2140CW
Hello Frederick, thank you for asking. it is only available as a complete Pump Filter PS3522306. Good luck with this repair.
Removed the top of the washer by removing the 4 back screws and 2 small brackets. Then I removed the front panel, this was actually the hardest part, 2 screws and 8 tabs that you pop out carefully from the top of the panel. I only disconnected the power button and was able to rest the panel on top of the washer. The rest of the washer came apart quickly just moving down the front of the washer and removing the door, latch, tub gasket, drain cover. Removing the pump was just a mater of disconnecting the drain hoses, and one clip under the drain assembly. 3 screws attach the drain to assembly to the pump and only 2 wires that are clearly marked. Reassembly is just going back through in reverse order of disassenbly. The best thing about this is that it all comes apart with a standard phillips screwdriver.
I first tested the motor per the service manual. I checked the resistance between the terminals of the 3 pin connector. It's supposed to be 5-15 ohms. The motor checked out so I replaced the main electrical board. It turns out that wasn't the problem. After a brief web search I found out that the hall sensor (which is attached to the motor stator) was the likely cause of the failure. I replaced that and everything works great now. And now I have a spare main board in case that ever fails. I also want to mention that I took the time to remove the dispenser box (where the water comes in and is directed to the different cleaning products) and cleaned it with a very strong bleach solution. It got rid of the mildew and funky smell. It seems that the fabric softener caused a lot of mildew to form inside the dispenser directly above the fabric softener tray. The bleach took care of that. This is probably something that should be done routinely to keep the mildew from forming.
There is a magnet at the bottom of the door which allows the door to be held ajar when the washer is not in use to allow the tub and gaskets to dry. A tab on the plastic housing which retains the magnet broke which allowed the housing to pull free of the door and stick itself to the machine preventing the door to close. Easy fix to replace the magnet was $18. Instructions were included in the box. Part number on the drawing was A165. PS3618292 Magnetic Door Plunger
