This part helps keep your front-load washer safe and working properly. It locks the door during cycles so it doesn’t open unexpectedly, and it also tells the washer when the door is shut so it can sta...
Introducing the Hex Head Bolt, a vital component designed to keep your Samsung, Kenmore, or Maytag washer functioning at its best. Manufactured with strict quality controls, this part ensures you rece...
Revive the wide array of your appliances including your Samsung Refrigerator, Samsung Dryer, Samsung Washer, and even your Samsung Dishwasher with the Tapping Screw, a crucial component engineered by ...
Optimize your Samsung, Maytag, or Kenmore washer's performance with the Drain Pump Assembly - 120V 60Hz. This high-quality unit directly replaces the original drain pump, ensuring efficient and smooth...
Upgrade your domestic laundry routine with our Washer Tub Gasket/Seal. Designed by leading brands, Samsung and Maytag, this product is designed for maximum efficiency and durability. Guaranteed to fit...
Have you noticed your Samsung washer is not operating as efficiently as it used to? Or Perhaps you've spotted a leak? It's likely because there is a tear or wear in your door boot seal-gasket. Our r...
Is your Samsung washing machine door glass broken or cracked? We've got just what you need to fix that problem. Introducing our Samsung Washer Door Glass ? a reliable, high-quality replacement part cr...
Introducing an integral element for your washing machine maintenance, Samsung's oil seal. This essential component is expertly designed to be pressed into the rear drum of your washer, thereby providi...
Everything you need to keep your Samsung or Maytag washer working properly can be found right here. The Drain Pump is essential in ensuring your washer operates efficiently, smoothly channeling water ...
Introducing the highly efficient Water Inlet Valve, exclusively designed for your Samsung, Maytag, and Kenmore washers. This essential component ensures a controlled and steady water flow into your wa...
1. remove the three screws from the top backside of the top panel 2. push the top panel to the rear 1/8 to 1/4 inch 3. lift/rotate top panel from rear to front, set aside. 4. remove the three wire connectors from latch. 5. use #15 Torx to remove the three screws from the latch. 6. remove and replace part using top opening. 7. reverse order to finish.
I bought a new door lock for 132 dollars (item number PS2037196).
Ultimately you have to get to the inside of the machine where the door lock is located in order to see if you will need this door lock that I bought.
DISCONNECT POWER FROM MACHINE.
First take off the top by taking off the 2 screws on the back of the machine.
Second take off the control panel, I believe there are about 5 or 6 screws for that. (there's also a screw when you open up the detergent compartment on the bottom left- also, a lever must be pushed in order for the compartment to come off- it MUST be taken off).
Third unscrew the top of the front white plate.. there should be a 5 or 6 screws for that. You don't need to take off the entire front plate.
Finally unscrew 3 screws that hold the door lock in place .. make sure your hands is in the machine- the back of door lock to catch the lock when you're on the last screw.
Gently take out the door lock from the side with the cables attached by holding the white metal door open (it bends).
Try to pull on the bottom of the door lock (its a manual release). If it doesn't release you need to buy a new door lock like I did... if it does release then you don't need a door lock and just reassemble. (Note: You can also try plugging in the machine and THEN pulling down on the manual release. When I tried this the door lock just vibrated and nothing happened so I bought a new door lock.)
If you have the new door lock continue here:
Take out all 3 cables on the old door lock by pressing on the corresponding clips.
Attach the new door lock with the correct cables. Assemble machine back together.
