This dishwasher door gasket creates a watertight seal between the door and the tub, preventing leaks during wash cycles. Made from flexible black rubber, it fits securely along the edge of the door to...
If your dishwasher isn’t draining or cleaning well, this drain pump could be the issue. It helps move water out of the tub during the cycle and fits many Bosch, Thermador, and Gaggenau models. Signs i...
If your dishwasher isn’t filling with water, running dry, or leaking, the water inlet valve might be the issue. This part controls how much water flows into your dishwasher during each cycle. It’s des...
Ensure proper detergent release during wash cycles with this genuine latch kit, designed to open the detergent cup at the right time and prevent premature opening. The kit includes a latch, spring, an...
Ask our experts a question about this model and we'll get back to you as soon as possible!
2 questions answered by our experts.
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
James
November 14, 2023
Machine makes noise only when in fill cycle ( start cycle)
No noisy at drain cycle any idea it’s a Bosch dishwasher
For model number SHV46C03UC
Hi James,
Thank you for your question. If you hear a loud noise when the dishwasher is filling with water, it may be the water inlet valve closing. This will cause the water pipes to rattle and you will hear a hammering noise. We hope this helps!
Was this helpful?
Thank you for voting!
Leanne
March 2, 2025
Clear Water accumulates in the bottom of dishwasher between washings… enough to leak out sometimes.
For model number SHV46C03UC
Hi Leanne, thank you for getting in touch. This is normally a sign the water valve is "stuck" open and allowing water into the tub when not in use. The valve would need to be replaced. We hope this solves your problem!
With the help of You Tube, this 50 year old Mom got the job done. Not that complicated if you watch the step by step instructions on the Appliance Pro video. My repairman and husband were both determined to just buy a new one but this 20 year old dishwashing genius was just in need of a little repair. Only need a screwdriver, and slightly confusing as wires hook on a little different on new pumps. I suggest watching video the whole way through and then playing it step by step as you do the repair. Worked great for me. Thanks.
I used a wet vac to remove the water from the dishwasher. remove cover and filter/strainer from bottom of dishwasher. remove screw which allows you to lift the plastic piece to access check valve. Original check valve looked like new , I installed new check valve re installed parts . Job done and issue resolved .
There are two ways to do this repair: the "right" way and the hard way. I chose the hard way, as the right way involves disconnecting the dishwasher plumbing, removing the dishwasher from under the counter, taking all the outer panels off, and disabling the door springs. There are good YouTube videos on this. The hard way doesn't involve that -- but is not all that easy and I'm not sure I'd recommend it. The problem, in essence, is that to install the new seal there is now way to do it without taking the door off the machine and taking the door apart -- which requires that the springs be locked out, if not disabled.
I accomplished that part of it by opening the door, partially, undoing the two screws on each side which hold the hinges, taking the front panel off (piece of cake, with a Torx driver),slipping the door partly off the hinges, and then locking the hinges open with the pry bars.
There are an assortment of ways one could seriously damage either the door or one's self doing it that way -- the hinge springs are very powerful -- so I don't recommend my approach.
