This dryer drum belt from Amana has five ridges and is 93-3/8" inches in length, and 3/8 of an inch wide. It is flat, black in color, and is made entirely of rubber.
Meant as a backup to a high limit thermostat, this fuse is typically set to trip at a higher temperature than that of a high limit thermostat. This is a one-time use fuse, so when it does trip, you do...
This dryer drum glide pad is an inch long. It is made of a felt material and is used for gas and electric clothes dryers.
$10.20
In Stock
Questions And Answers for SDE3606AYW
Ask our experts a question about this model and we'll get back to you as soon as possible!
9 questions answered by our experts.
< Prev
1
2
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Pete
November 27, 2019
Does the belt tension pulley include the spring
For model number SDE3606AYW
Hello Pete, Thank you for the question. The Spring PartSelect Number: PS11742854 is sold separate from the Pulley. Hope this helps!
Hi Tim,
Thank you for your question. The dryer has a capacity of 7.1 cubic feet. We hope this helps!
1 person found this helpful.
Was this helpful?
Thank you for voting!
Linda
November 30, 2019
Drum will not turn with a regular load of clothes. Can only put in a few pieces at a time in order for it to turn. Also seems temp is pretty warm but assuming it is because drum is not turning as it should
For model number SDE3606AYW
Hello Linda and thanks for writing.
There are a few parts that you need to check :
Belt # PS11742271 (this is the most likely part in need to be replaced) or the idler pulley # PS11757553. We hope this helps. Please contact us anytime.
S/n 12392801ej: Date of manufacture and specifications?
For model number SDE3606AYW
Hello and thank you for writing.
According to the serial and model number, this product may have been manufactured May of 2004.
For your convenience, we have attached the link to your service manual. We hope this helps. Good luck with your repair.
https://partselectcom.azureedge.net/assets/manuals/B781165D1AA66A8F211E0F63D68C7FCED4EE93AE.pdf
https://partselectcom.azureedge.net/assets/manuals/28CAAC894A26A486A70F96F7DBF4745A7DD4D7BD.pdf
1 person found this helpful.
Was this helpful?
Thank you for voting!
Roger
November 29, 2019
Dryer develops a squalling noise after warming up.
For model number SDE3606AYW
Hello Roger, thank you for writing. You will want to inspect the Drum Support Rollers, part number PS11741913 for wear, as they could be making the noise. You will also want to consider the Multi Rib Belt, part number PS11742271 for your dryer as the cause. I hope this helps!
Was this helpful?
Thank you for voting!
< Prev
1
2
Next >
✖
Ask a Question
Ask our experts a question on this model and we'll respond as soon as we can.
The first thing I did was to unplug the dryer from the wall. Then I removed the bottom two screws and slid the bottom cover off so i could see all the way to the back, I tipped the dryer back against the wall and searched for the problem with a flashlight. I noticed that one of the guide wheels that held the drum in place was sheared off. I took the new drum support roller out and carefully slid it over the shaft, I had to jiggle it around for a bit, but then it finally was seated correctly. I replaced the washer and then the clip using a pair of needle nose pliers and a regular screw driver and then turned the dryer by hand to see if the wheel came off. After confirming that it worked, I put the cover back on, and plugged it in and tested it.
I pulled the bottom panel and the door panel to replace the manifold and felt gasket around the drum. I removed old gasket very easily, it peeled right off. I use brake cleaning fluid (Spray Can from Auto Zone about $1.45) to remove old glue. Used spray contact cement (Elmer's about 4.50 at Ace) and sprayed the panel and gasket surfaces and let dry. I then applied a 2nd coat and let get "tacky" and installed the gasket. You will need an extra set of hands to hold the gasket in place while you stretch it over the the panel. The vent manifold is held in place with 3 phillips screws and was installed in about 10 minutes. The only gripe I had was in the Parts-Select illustrated breakdown they don't tell you the lint screen comes with the manifold assembly, so I bought one of them too. Now have an extra lint screen
Took it out of the box and put it in the dryer. I could not find this part anywhere else but on this website. The item was delivered the next day to my surprise.