RG2300NGPCBB General Electric Refrigerator - Instructions

After verifying that my water solenoid valve did open and close (I removed the solenoid and put my own 120vac on it and blew through it) and then I verified that I was receiving my 120vac from the ice maker itself I knew my problem was in the ice maker itself. Just removed the mounting screws holding the old ice maker and it lifted out of place after unplugging the unit from electrical connection at the rear of the cabinet. Reversed the process for installation. Power unit up. Bleed air out of the water line feeding the watermaker. Waited a couple of hours and my first cubes where there. Filled up quick! Thanks.

Ordered the complete kit minus the water tap. Should have ordered that also. Install was difficult simply because I was not sure of the style of the fridge. No ident had been left on the unit, so I used the p;ictures in the install kit to decide the proper install. Was very quick and the parts were great. After I went under the house(crawl space) I found an old water tap which broke off in my hand and started spewing water. Replaced everything and it runs great. Nice kit with a lot of instructions. Fantastic ordering fromyour company. Next day delivery was unexpected.

My wife and I decided to tackle this job on a Saturday. The fridge was due for a good cleaning anyway. We pulled it out and shut off the water to the ice maker.
I took out the old ice maker, (two screws and the plug) Then went to the back of the fridge. removed the cardboard cover at the bottom of the frigdge and took the mounting screw out of the water valve. I had a double valve for the no longer working in-door water so I made sure to identify Then installed the new water valve. Note: be sure to check your connections for leaks before mounting the water valve - it is easier to see and fix them !!!! You can leave the water on at this point because the icemaker and water valve will not operate until the icemaker is plugged in. Next choose the right water fill cup, and install the ice maker to the existing screw mounts and plug in the connector. Note: be sure the ice maker is turned off. Start the fridge, let it get cold, then turn on the icemaker.
Overall this is a great multi install package - Don't worry about extra parts because you will have some. If we would have just needed to do the icemaker and not clean the fridge, I could have done it in about an hour.
Overall I would highly recommend this package vs what is available at other retailers for more money. Best Buy has a bargain replacement icemaker but does not have the versatility and completeness of this product. I give this product 5 stars.... dm

By following the instructions in the manual that went with it, I used the parts in the order that the instructions said. The illustrations were very easy and now we dont have to use ice cube trays any longer. Any person without experience that can follow directions can put in an icemaker with the simple to follow instructions that was used in the manual.

Unplugged the old ice maker. Removed the two screws that held it in. Removed the old ice maker and replaced it with the new one. Put back the two screws, plugged it back in and turned on the power switch. It started making and dropping ice in the first 1/2 hour.

Watched video, however could not get outer casing off. Under the panel are three small holes, pushed up with an Allen key, used a small screwdriver to wedge out, came out easily, followed instructions from video on removing and replacing solenoid

Removed panel from front of freezer door by pushing up on three spring loaded screws located in the opening where the ice door opens and closes. they are about 1 inch apart on the bottom of the opening. Push up to free ice maker panel. Remove three screws from solenoid, located at the top right. Remove wire, replace with new and that is it. Fixed the problem!! Our ice maker hadn't worked for months. Be careful if you remove the round ice maker door to clean. There is a spring that located on the left side of sprocket. The spring fell off and took me a while to figure where it came from. Recieved package in three days and the job took minutes. Works great! Very easy to complete.

I removed the bin and dumped out all the ice then I took out the two screws holding the icemaker to the freezer wall. I then unplugged the icemaker. Since all of the funnels etc were in place I simply plugged in the new icemaker, installed the two mounting screws, slipped the icemaker in place tightened the screws and turned it on.I'm happy to say the new unit is much faster than theold one. By morning I had a full bin of cubes. Thanks so much for your help.

I removed the outer plate by sticking a very small screwdriver in the small holes at the bottom of the plate and pulling the plate toward me.
I then removed the 4 screws from the internal plate and pulled the plate toward me.
Then I romoved the 3 screws holding the old solenoid and unplugged it.
Next I put the new solenoid in place and replaced the three screws.
Finally I plugged in the solenoid and replaced the internal and external plates.

several times I had to remove the ice maker door solenoid due to it sticking. I ordered a new one from parts select. Problem solved!!!

Ice maker not working. Received my order in 30 hours. (Excellent) After installing ice maker and water valve, I noticed that where the water enters through the freezer to the ice maker spout, there was a frozen spot in the connector. After melting the ice blockage with a hair dryer, the ice maker and water valve began working. No problem since. Unit working perfectly.

remove the front plate. use screwdriver to pry the cover off from the bottom of the cover, remove the wiring from the front cover.remove the 4 screws and pull out the shute. remove three screws from the solonide and replace . very easy fix. save yourself $100.00 labor.

Changing out solenoid was very easy, but you don't have to remove trim ring and it didn't fix my problem. Turns out a relay fell out of its holder in the piece you have after removing the 4 screws per the video.

Ordered new solenoid so the flap would close. That did the trick.

Take the face (the part with the buttons on the outside) off, disconnect wired connectors (three), take the screws out of the part behind that (4), and then find the solenoid value (on the right). It's attached with three screws. Mine was rusted beyond belief. I knew this was the problem, ordered a new solenoid valve, put it back in place with three screws (use new screws that fit, not the old rusty ones if possible). When testing, make sure you give the flap a couple of seconds to close. There is a delay, and I initially wasn't patient enough so I had to disassemble and assemble an extra time because of this.

Simply put: If your solenoid value is rusted and the value won't operate smoothly, order the part and install it. This is as easy as any repair could be.