This oven light cover is made of durable, clear glass and includes a protective seal to keep the interior light shielded from heat, grease, and debris while allowing bright, even illumination inside t...
$122.60
In Stock
Order within the next 11 hrs and your part ships today!
This rubber feet kit includes four non-slip feet designed to provide stability and vibration reduction. They help protect surfaces while keeping the appliance securely positioned during use.
$85.23
In Stock
Order within the next 11 hrs and your part ships today!
This black star burner cap is a genuine OEM replacement for select gas ranges. Sized as a Size F cap, it helps protect the burner from debris and moisture while supporting even heat distribution. A da...
$94.79
In Stock
Order within the next 11 hrs and your part ships today!
This genuine OEM halogen light bulb provides bright, focused illumination for appliance interiors such as ovens, ranges, and refrigerators. Designed for high-temperature environments, it delivers reli...
$67.43
In Stock
Order within the next 11 hrs and your part ships today!
This potentiometer, also known as a spark ignition switch, sits behind a range or cooktop control knob and translates the rotation of the knob into electrical signals that regulate burner heat and ens...
$98.75
In Stock
Order within the next 11 hrs and your part ships today!
This oven temperature sensor is designed to accurately measure the internal temperature of the oven cavity and relay that information to the appliance’s electronic control system for precise heat regu...
$199.26
In Stock
Order within the next 11 hrs and your part ships today!
Questions And Answers for PRD48JDSGU
Ask our experts a question about this model and we'll get back to you as soon as possible!
1 question answered by our experts.
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Randy
October 10, 2023
what is the number for the conversion kit to propane i will using a tank will it give me enough pressure for all 6 burners
For model number PRD48JDSGU
Hello Randy, thank you for contacting us. The compatible LP conversion kit for your model is part number PS8724790. When connecting the unit to propane gas, make certain the propane gas tank is equipped with its own high pressure regulator in addition to the pressure regulator supplied with the range. To operate 6 burners you will require the maximum gas pressure of 14 inches water column from the propane gas tank. We hope this information helps!
The sole review for this part by Andrew was most helpful and accurate with one exception: he said that there were two nuts Which needed to be removed in order to pull off the front knob panel. There were actually two on each end for a total of four, which confused me, as I wondered if I had the right ones. Another thing that would be helpful for somebody considering doing this repair is to know that it takes a deep quarter inch socket With two 6 inch extensions to reach these nuts through holes in the interior side panels. Also, take a look at the replacement potentiometers, and you’ll see that there’s a slot that can be lined up so that they can be pulled off the side of the shaft rather than off the front of the shaft. This repair took me about six hours. I’m mechanically inclined and work methodically, but since I’ve never done this repair before it was quite time-consuming.
Remove slide racks from oven. At the back right corner of oven unscrew heat sensor probe. Access rear of range. Remove screws holding back panel. Find wire from temperature probe where it passes through back wall of over and unclip it pulling probe wire and probe out back of oven. From the inside of oven, push chopstick through hole probe wire was routed through, to find hole in back wall of oven. Once chopstick is visible from back of oven, with chopstick enlarge hole through visible insulation. This is the opening the new probe wire needs to be routed through. From inside oven push new wire, using chopstick, through this hole and reattach wire at back of oven using the plastic clip on the wire. From inside oven screw probe to back of oven wall, reattach outside panel to back of oven, turn gas back on, plug range back in, check oven operates, and push range back in place, reinstall racks. You may have to remove oven door if you have trouble reaching to the back of the oven to access the probe. YouTube videos are easy to find showing how to do that.
