This manufacturer-approved Refrigerator Door Shelf Bin is made of white plastic and is easy to install. It is used to hold heavier items in the fridge, and you'll be able to visually see if the part i...
Glass only. This glass insert measures 23.82 x 15.50-in. This is an authentic Frigidaire replacement part. The crisper shelf insert is designed by the manufacturer for use in refrigerators. This part ...
This is a replacement door bin for your refrigerator. It is made of clear plastic and is approximately 13 inches wide at its longest point, 5 inches deep, and 4 inches tall. The door bin holds items t...
This 3.8-watt LED light bulb is designed to illuminate the interior of select refrigerator models, providing bright and efficient lighting when the door is opened. If your current bulb is dim, flicker...
This is the replacement meat pan for your refrigerator. It is made of clear plastic and is approximately 18 inches long and 13 inches wide. The meat pan slides into the bottom of the refrigerator shel...
If your fridge isn’t staying cold or seems noisier than usual, the door gasket might be the problem. This black rubber seal runs around the edge of the door and keeps the cold air in. If it’s torn or ...
This evaporator fan motor is located in the back of the freezer, and circulates air over the refrigerator coils. These coils will convert the heat into cool air, which is then circulated.
This dairy door, also known as a dairy bin cover, is a genuine OEM replacement part for your refrigerator. The dairy cover is a plastic part that serves as a covering to a shelf on your fridge door, t...
Need a solution for your malfunctioning refrigerator drawer? We've got you covered with the right-side Drawer Slide Rail, a genuine replacement part from Frigidaire. This part plays a crucial role in ...
$81.48
In Stock
Questions And Answers for PLRU1778ES3
Be the first to ask our experts a question about this model!
✖
Ask a Question
Ask our experts a question on this model and we'll respond as soon as we can.
The repair didn't require any tools at all. Just simply slide the new glass shelf carefully into the the frame and while holding it horizontally slide the frame back into the rails. This took less than a minute to accomplish. Very satisfied with the results.
After silencing the alarm, it seemed to be running as normal without any unusual noises, but food was starting to thaw from the top shelf on down and condensation was dripping from the roof. We were able to place most of the food in 2 large ice chests and then the rest in the freezer compartments of 2 fridges we have in the house. I then turned down the temp dial to the coldest setting and let it run for an hour or so; no change.
After researching on the internet, it sounded like our symptoms could be pointing to a defrost timer issue. I pulled the freezer away from the wall, located the timer and used a large screwdriver to slowly advance it. While doing this, at one point I could hear the compressor kick in. I pushed the quick freeze button and let it run for a while. When I checked it in a few hours, the alarm light had gone out and water that I had placed inside was frozen. We took a chance and put the food we placed in the ice chests back in the freezer. Everything was fine several hours later.
I ordered a new defrost timer, it arrived in a couple of days, and replaced the old one with it in a matter of minutes by disconnecting the wire harness from the old timer, removing the 2 screws holding it onto the bracket, screwing the new timer to the bracket, reconnecting the wires harness, and done. It's been a week or so and no problems.
Unplugged unit from power source. Emptied the vegetable crisper and the removed crisper including the permanently fixed mounts on either lower wall of the unit which are retained with screws. Removed temperature control knob. Then removed interior back panel that covers cooling panel and controller. Carefully work panel loose as it is very thin and bendable metal. Note gaskets at each end of the panel and save for re-install. After working panel loose carefully find controller and pinch the mounting bracket of the controller which allows it to release from the panel. Now you may set panel out of the way and continue disassembling the controller. It has a thermal wire that is mounted to the back of the fridge wall with a screw clam. Note position and shape then remove. Remove ground and power connections noting position of each. Take new controller and attach ground and power connection. Bend thermal wire using thumb as a shaper to exacting shape of the old one and position in clamp and secure with screw. Note old controller had a Styrofoam cover and return this cover after attaching new controller to the cover panel. After this, reposition the cover panel and retain with screws but don't tighten screws all the way as you need to be able to shift panel while replacing gaskets at the ends. Place the end gaskets where they originally were and work both in until they seat. Tighten screws on the panel. Replace crisper and plug in. Good luck it fixed mine and the unit works great.
