PDW8000G01BB General Electric Dishwasher - Overview
Sections of the PDW8000G01BB
[Viewing 4 of 4]
Manuals & Care Guides for PDW8000G01BB
Click to downloadKeep searches simple, eg. "belt" or "pump".
Water Inlet Valve
PartSelect #: PS3654179
Manufacturer #: WD15X10014
This water inlet valve should be located behind the lower kickplate panel in either the right or left corner. The attaching solenoid on the valve open and close according to the desired amount of water needed.
$85.06
Special Order
Door Seal
PartSelect #: PS651625
Manufacturer #: WD01X10120
It provides a seal between the tub and the door.
No Longer Available
Upper Dishrack Wheel
PartSelect #: PS259051
Manufacturer #: WD12X10032
This wheel is sold individually. It comes with an attached axle.
No Longer Available
Fold Down Clips - Set of 2
PartSelect #: PS258069
Manufacturer #: WD01X10046
These clips are sold in a pair. They are used in conjunction with the front and rear inserts for the lower dishrack.
$88.96
Special Order
Complete Upper Rack Assembly
PartSelect #: PS959346
Manufacturer #: WD28X10123
This rack comes with wheels and spray arm.
$1170.75
Special Order
Rear Basket Insert
PartSelect #: PS651723
Manufacturer #: WD28X10084
Sold individually.
No Longer Available
Front Basket Insert
PartSelect #: PS651724
Manufacturer #: WD28X10085
Sold individually.
No Longer Available
Questions And Answers for PDW8000G01BB
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Symptoms of the PDW8000G01BB
[Viewing 4 of 4]Leaking
Fixed by
these parts
these parts
Show All
Will not fill with water
Fixed by
these parts
these parts
Show All
Not cleaning dishes properly
Fixed by
these parts
these parts
Show All
Not draining
Fixed by
these parts
these parts
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Water leak, small puddle to front left of dishwasher
You'll need to remove the front toe kick and (if installed, the GE Profile baffling for additional silencing action).
You will need to disconnect the right wire connection to access the right screw (and may need to use a flat head screwdriver). You can then remove the 2 screws that hold the Valve Water Inlet on.
You will then need to loosen and the hose clamp that attaches the water line to the Valve Water Inlet. You may need to force it undone since the rubber connection is pretty secure around the water tube inlet.
Disconnect the plastic wire housing from the Valve Water Inlet and you should now have the Valve Water Inlet disconnected.
Reverse the order and reconnect everything and you should be good to go!
Double-check for any leaks prior to pushing everything back in :)
You will need to disconnect the right wire connection to access the right screw (and may need to use a flat head screwdriver). You can then remove the 2 screws that hold the Valve Water Inlet on.
You will then need to loosen and the hose clamp that attaches the water line to the Valve Water Inlet. You may need to force it undone since the rubber connection is pretty secure around the water tube inlet.
Disconnect the plastic wire housing from the Valve Water Inlet and you should now have the Valve Water Inlet disconnected.
Reverse the order and reconnect everything and you should be good to go!
Double-check for any leaks prior to pushing everything back in :)
Parts Used:
-
Greg from Burlington, VT
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Socket set
65 of 85 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Leaking water when in use.
Part was an exact match. Make sure to use plumber's tape on all threads. Had to really tighten fittings to prevent leaks. Screws are a little difficult to get to. Test for leaks first, before final installation.
Parts Used:
-
J from Walnut, CA
-
Difficulty Level:Easy
-
Total Repair Time:1- 2 hours
-
Tools:Pliers, Screw drivers, Socket set
16 of 22 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Dishwasher was leaking.
Removed the wire clip, then removed two screws on mounting bracket. Then disconected the hose. Removed the brass elbow.
Then reversed these steps and I was done.
Then reversed these steps and I was done.
Parts Used:
-
James from Grand Isle, VT
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Pliers, Screw drivers
11 of 19 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!