MWS939ZAS0 Frigidaire Washer - Overview
Sections of the MWS939ZAS0
[Viewing 4 of 4]
Keep searches simple, eg. "belt" or "pump".
Drive V-Belt
PartSelect #: PS1146950
Manufacturer #: 134511600
This belt is made to slip on the motor pulley to bring the basket up to the speed required and this makes the belt get wear and tear.
$30.95
In Stock
Order within the next 9 hrs and your part ships today!
Screw
PartSelect #: PS417463
Manufacturer #: 131302800
This is a replacement screw for your washer or dryer. The screw is approximately half an inch in length and is a Phillips-head screw. It screws in from the outside of the drum, into the vane/baffle. T...
$27.85
In Stock
Order within the next 9 hrs and your part ships today!
Drain Hose
PartSelect #: PS417877
Manufacturer #: 131461200
This part comes with a ninety degree elbow.
No Longer Available
Screw-In Plastic Leveling Leg
PartSelect #: PS1152204
Manufacturer #: 134548800
Sold individually.
$32.89
In Stock
Order within the next 9 hrs and your part ships today!
Tub Seal Assembly
PartSelect #: PS459481
Manufacturer #: 5303279394
This seal helps prevent any leaking around the transmission of washing machines.
$113.03
Special Order
Washer Lid Lock with External Safety Switch
PartSelect #: PS648775
Manufacturer #: 134101800
Mounting bracket on this part replaces old style ( You may need to drill off old bracket before mounting new lock).
No Longer Available
Dual Action Agitator
PartSelect #: PS418275
Manufacturer #: 131605901
This agitator helps your washer clean clothes better by moving them around during the wash cycle. It spins back and forth to mix water and detergent evenly, loosening dirt and keeping clothes from get...
$193.08
In Stock
Order within the next 9 hrs and your part ships today!
SCREW
PartSelect #: PS417085
Manufacturer #: 131168200
Sold individually.
$29.12
In Stock
Order within the next 9 hrs and your part ships today!
Tension Idler Pulley
PartSelect #: PS418897
Manufacturer #: 131862900
This idler arm assembly comes with the pulley wheel.
No Longer Available
Spin Bearing
PartSelect #: PS446536
Manufacturer #: 3204405
$111.70
In Stock
Order within the next 9 hrs and your part ships today!
Upper Spin Bearing Washer
PartSelect #: PS473382
Manufacturer #: 5308002401
$29.12
In Stock
Order within the next 9 hrs and your part ships today!
Questions And Answers for MWS939ZAS0
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Symptoms of the MWS939ZAS0
[Viewing 8 of 8]Leaking
Fixed by
these parts
these parts
Show All
Will not agitate
Fixed by
these parts
these parts
Show All
Burning smell
Fixed by
these parts
these parts
Show All
Will not drain
Fixed by
these parts
these parts
Show All
Spins slowly
Fixed by
these parts
these parts
Show All
Noisy
Fixed by
these parts
these parts
Show All
Will Not Start
Fixed by
these parts
these parts
Show All
Spinning Issues
Fixed by
these parts
these parts
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
replace broken drive belt
carefully pry up on front washer top to release plastic keeper pins,remove 2 phillips screws from beneath lower front washer panel,slightly lift upward on panel to release.remove old broken belt,push new belt beneath large tub pulley,put belt on small motor pulley,push back belt tension /idler arm,start belt on large tub pulley,turn tub pulley by hand to run belt on,release tension on idler arm.replace front panel and lower top.WALAAH!!!! you are done.
Parts Used:
-
rodney from fairfield bay, AR
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
281 of 315 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Clicking due to agitator dogs slipping
One bolt (after removing the fabric softener dispenser and a water tight cover you will see it). Remove the bolt and slide it straight up and then it's the reverse to put in the new one. Very simple repair and very inexpensive if you willing to do it yourself.
Parts Used:
-
BRIAN from UPLAND, CA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Socket set
81 of 102 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Lid Lock Assembly broke
The Lid Lock Assembly came super fast! The install would have been flawless, but the "pre-drilled" holes on the new Lid Lock Assembly were way to small. We found that out after we had reconnected the wires and gotten it into place. Aside from that small set back, the install went great! This repair is definitey not one that you would need to pay a repair person to do!
Parts Used:
-
Jenessa from Tacoma, WA
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
76 of 95 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!