This front glide kit comes with a blue plastic glide, a brown cork pad, and two metallic rivets. Two kits are required per appliance. A rivet tool is required for this installation.
This gas dryer ignition coil set comes with two ignition coils: one three-terminal boost/hold coil, and one two terminal secondary coil. Usually only one of them burns out but you should replace them ...
At 91-5/8 inches in length, this dryer drum belt from Maytag has five ridges. It is all black in color and is made entirely of rubber. This flat belt is 3/8 of an inch wide.
This is a rectangle shaped lint filter screen used for some gas and electric clothes dryers. The dimensions of this lint filter screen are approximately twelve and a half inches long by seven and thre...
Also known as the door boot seal. This part includes the drain and plug. The seal is located around the door of the washer to prevent water from leaking.
This flat style igniter comes with a wire harness connector. This part ignites the gas within the dryer. Bracket is NOT included.
$48.60
In Stock
Questions And Answers for MLG2000AWW
Ask our experts a question about this model and we'll get back to you as soon as possible!
5 questions answered by our experts.
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Anna
December 22, 2019
The washer started leaking. Checked the hoses. Everything is in good condition and they are dry. What might be the problem?
For model number MLG2000AWW
Hi Anna,
Thank you for your question. If the washer is leaking, there are some parts that you will need to check to see which one is causing the issue. You will need to check the hoses, the pump, the tub cover gasket, the water inlet valve, the bellow or door boot seal, the water level switch, the door catch and the tub seal. We hope this helps. Thank you and have a great day!
Was this helpful?
Thank you for voting!
Joseph
February 24, 2020
I push the start button for the washer and sometimes it shuts off within a minute and the door doesn,t lock and other times it will shut off mid way through the first cycle.What should i do?
For model number MLG2000AWW
Hello and thank you for writing.
It certainly sounds like it could be a faulty door switch PS1964648 and/or possibly a malfunctioning door lock switch PS11739335 you should check the part(s) for signs of damage or test with a multimeter, and replace the part(s) as needed. We hope this helps. Please contact us anytime if you require further assistance.
Where is electronic control board ps11739517 located in this unit? What picture on your unit overview is this part located???
For model number MLG2000AWW
Hello Tom, thank you for your question. This electronic control board is located in the cabinet front dryer section. The link to the diagram is attached, please refer to diagram number 22. We hope this information is useful.
Hot water fill valves is not operating. Washer will only admit cold water.
For model number MLG2000AWW
Hi Merrill, thank you for getting in touch. Based on the description that you have provided, we would recommend checking the inlet hose for any blockage or damage. If that is not causing the issue, then the water inlet valve part number, PS11739363, is most likely faulty and may need to be replaced. We hope this helps!
tienen la tarjeta de este centro de lavado y cuanto cuesta por favor
GRACIAS
For model number MLG2000AWW
Hola Óscar, gracias por comunicarte. El tablero de control electrónico para este modelo aparece como número de selección de pieza PS11741047. ¡Buena suerte con la reparación!
first, I unplug the power supply of the dryer then I removed the two screws at the bottom of the dryer then pulled out the front part of the dryer,unplugged the blue & yellow wire for the on/off switch for the door,at the back of the dryer I unscrew the pannel for the belt,disconect the belt,and I unscrew the four screws on both side of the front pannel to remove the front cover of the drum. Once I removed the front cover of the drum I can now remove the drum itself to access the drum support roller. I unscrew the rollers then replace it with the new once. It was an easy job. Thank you.
