Also known as a door boot seal.This part is used to keep the clothes inside the tub during the wash cycle. The folds in the bellow allow the tub to move separately from the door during the spin cycle.
This 18 ml bottle of white appliance touch-up paint is used to cover scratches or marks on your appliance. The white touch-up paint can be used on refrigerators, microwaves, ranges, clothes dryers, an...
This is a replacement tub-to-pump hose for your washer. This hose runs from the bottom of the tub to the water pump, and is used to transport water. The hose can develop a hole, and when this happens ...
This water inlet valve attaches the water lines to the back of your appliance. The attaching solenoids on the valve open and close according to the desired temperature or amount of water needed.
This is the replacement bellow clamp for your washer. It is approximately 18 inches in diameter and is sold individually. The bellow clamp goes around the bellow in your washer and holds it in place o...
The door boot spring clamp or outer bellow clamp on your washer is designed to keep the door boot in place. It is circular in shape, and you will find it wrapped around the bellow. To remove the old c...
This hose clamp extends from half an inch to an inch in diameter. It is made entirely of metal and is intended for use with Maytag brand washing machines.
$11.68
In Stock
Questions And Answers for MHWZ400TQ02
Ask our experts a question about this model and we'll get back to you as soon as possible!
4 questions answered by our experts.
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Tracy
March 4, 2020
Will a stacking kit for a Whirlpool machine work for this model as well. Stacking kit is available at home depot, would it work? I checked your website to see what your kit would look like, but there doesn't seem to be a photo available. Please help... thank you in advance
For model number MHWZ400TQ02
Hello , Thank you for writing. Sadly, the part you are requesting we do not have listed. We strongly recommend you contact the manufacturer, as they would have this information in their system. Ask them for the part number you require and contact back to see if it is something we carry. We hope this helps.
1 person found this helpful.
Was this helpful?
Thank you for voting!
Marilyn
August 31, 2021
The drum does not move at all and it did not spin the last cycle. All lights work
For model number MHWZ400TQ02
Hello Marilyn, Thank you for the question. If the dryer is still running and the motor is on but the drum is not turning, we suggest checking the Drum Belt. The main drive belt is designed to ride on the pulley until the basket gets up to speed. We hope this helps!
The drum on my frontloading washing machine doesn't turn anymore and last load finished quite wet. I did not previously ask a question about a dryer so my question never was answered.
For model number MHWZ400TQ02
Hello Marilyn, Thank you for contacting us. Normally if the appliance is working normally otherwise, we suggest checking the Drum Belt, PartSelect Number PS11754068. The main drive belt is designed to ride on the pulley until the basket gets up to speed. We also checked and seen the previous question on the dryer was answered and posted, we try to answer the questions as fast as we can but could take 24 hours to get an answer. If you need help placing an order, customer service is open 7 days a week. Please feel free to give us a call. We look forward to hearing from you!
When I press the power button, nothing happens. I checked the plug and breakers and they are fine. What is the problem?
For model number MHWZ400TQ02
Hi Pat, thank you for getting in touch. First, you may need to make sure the power button is not loose or damaged. If that is not causing the issue, then you may need to replace the electronic control board, part number PS11748533. We hope this helps!
Removed the front panel unplugged The washer drained water out, lift the washer up to un screw the drain pump. Then unhooked the hoses from pump put the other pump in.
I discovered water leaking from the bottom of the door on our Kenmore front load washer. I did a little self diagnosis from the internet and found that this seems to be a common problem for front load Kenmore washers and that the ususal suspect is the large rubbery bellows. I examined the bellows on my washer and although I didn't find anything wrong with it, I couldn't find any other likely causes. I shopped around and found PartSelect to be the cheapest for the replacement part. Removal is easy by removing the lower front panel with three small screws on the bottom front, then remove the very top panel and then the top front control panel and finally the door panel. the bellows are actually held in place with a spring loop on the outer and a screw tightener on the inner, both are fairly easy to remove and the bellows comes right off. For installation my best advice is to lube the bellows with a small amount of dishwashing soap in the groove that fits on the washer tub. This will help it slide into place and enables a small amount of sliding fine tuning once it is on. From there it is just a reverse of the removal.
Pump started making noises like ball bearings grinding. took the lower front cover off pulled the strainer out of the pump housing and found $2.55 in nickles dimes and quarters. Some 223 bullets and about 20 bobby pins. Together they had destroyed the impeller, so ordering a new one and installing it did the trick. Easy installation about 15mins.