This 18 ml bottle of white appliance touch-up paint is used to cover scratches or marks on your appliance. The white touch-up paint can be used on refrigerators, microwaves, ranges, clothes dryers, an...
Sold individually. These shock absorbers keep the washer from vigorous shaking during its cycles. This shock absorber is for washers.
Shock absorber absorbs the vibrations and movements of the oute...
This is a replacement tub-to-pump hose for your washer. This hose runs from the bottom of the tub to the water pump, and is used to transport water. The hose can develop a hole, and when this happens ...
Water inlet valve controls the water flow into the washer.
Fits some washers in the following series: Kenmore 110; Whirlpool CHW, WFW and YWFW; Maytag CHW, MHN, MHP, MHWE, MHWZ and YMHWE; Amana NFW...
This is the replacement bellow clamp for your washer. It is approximately 18 inches in diameter and is sold individually. The bellow clamp goes around the bellow in your washer and holds it in place o...
This part regulates the temperature of the water in the tub. The sensor is located in the heating element.
$47.60
In Stock
Questions And Answers for MHWE201YW00
Ask our experts a question about this model and we'll get back to you as soon as possible!
4 questions answered by our experts.
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Tony
January 16, 2024
My Maytag washer model MHWE201YW00 is able to wash, rinse and pump the water out, but skip spinning the drum to extract the water from the wet clothes.
To spin the drum, I wait until the normal washing cycle finishes then I select the spin function only, then it spins and extract the water from the wet clothes. This option sometimes it does not work
There is no Error Codes currently. I unplugged the power for an hour, but no luck.
What does it cause not to spin in this case in normal washing cycle?
For model number MHWE201YW00
Hello Tony, thank you for your inquiry. Based on the description that you have provided, we would recommend checking the control board, part number PS11753744, to fix the issue. We hope this solves your problem!
Codes F6 & E1 coming up and the MCU works fine but cycle not iniatining what parts do I need?
For model number MHWE201YW00
Hi Tiffany, thank you for reaching out. The F6E1 error code signifies a communication error between the main control and the motor control of your washer. If the MCU is working fine, then you may need to make sure there is no wiring issue between the two and all connections are properly made. Also, unplug the appliance for a few minutes and plug it back on to reset it. If the issue persists, then you may need to check the user interface control board, part number PS11753744, as it is most likely faulty. We hope this information helps!
Hello Laurie, thank you for reaching out. We have attached a video of the installation of the Temperature Sensor, part number PS11755214. We hope this information helps!
Hi Bill, thank you for contacting us. According to our research, there is a problem with your temperature sensor, part number PS11755214. If your issue is not resolved, please check your control board, part number PS11753744. We hope it helps!
Removed the front panel unplugged The washer drained water out, lift the washer up to un screw the drain pump. Then unhooked the hoses from pump put the other pump in.
Pump started making noises like ball bearings grinding. took the lower front cover off pulled the strainer out of the pump housing and found $2.55 in nickles dimes and quarters. Some 223 bullets and about 20 bobby pins. Together they had destroyed the impeller, so ordering a new one and installing it did the trick. Easy installation about 15mins.
This model is a front-loading washer. The spring loaded retainer for the front of the boot must be removed, then the boot can moved to the side exposing the module. Remove the two screws holding the model, pull the model out, remove the three electrical plugs, then reverse this procedure to install new module.