This drum support roller is sold individually. Most dryers require two. The tri-rings are included. This is a drum support roller for a dryer. It is a genuine replacement part. This part is sold separ...
The drum support roller kit (Dryer Repair Kit) allows the dryer to tumble properly by supporting the drum cylinder. The idler pulley provides the tension required for a multi-ribbed belt. The belt att...
If you notice that your dryer is noisy or will not tumble, you may need to replace the tri ring. This part is triangular, and is less than an inch in size. Tri rings can be found both on the idler pul...
This 18 ml bottle of white appliance touch-up paint is used to cover scratches or marks on your appliance. The white touch-up paint can be used on refrigerators, microwaves, ranges, clothes dryers, an...
If your dryer drum isn’t spinning, the motor might be the issue. This replacement motor works with many Whirlpool-brand dryers made before 1996 and comes with the pulley already attached. It powers th...
This kit includes one high limit thermostat with a limit of 250 degrees Fahrenheit, and one thermal cut-off fuse with a limit of 360 degrees Fahrenheit. The thermostat and fuse help prevent the dryer from overheating.
Brighten up your appliance with this easy-to-install 10-watt light bulb, perfect for dryers and refrigerators. It gives off a clear, steady light so you can easily see inside when the door is open. Wh...
The blower wheel is a squirrel cage type wheel whose purpose is to move the air through the room or appliance. The blower wheel spins on the motor shaft to blow air through the dryer drum and out through the exhaust.
This part senses if the igniter is hot enough to ignite the flame for heat, allowing the gas valve to open. The sensor is three inches long and is used for many gas clothes dryers. If your dryer is no...
This silicone carbide igniter with ceramic holder kit includes the 3" flat igniter, bracket, 4" wire leads, and the plug. It can replace both round and flat igniters. This kit is used for many gas clothes dryers.
$51.40
In Stock
Questions And Answers for MGDX655DW0
Ask our experts a question about this model and we'll get back to you as soon as possible!
3 questions answered by our experts.
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Cindy
January 21, 2023
Is there a lint filter replacement for this dryer?
For model number MGDX655DW0
Hello Cindy, we are glad you asked. Yes, the Lint Filter is part PS16543574. We are pleased to have been able to help.
Hi Joseph, thank you for contacting us. The timer control knob for your model is part number PS11756281. To remove the knob, pull straight out and it will come off the shaft. The hole in the back is keyed in the shape of a D. That needs to line up with the flat edge of the shaft on the washer. Line those up, and push it straight on to complete the installation. We hope this information helps!
Wrinkle Control knob came out with shaft attached to it does the control unit need to be changed or just a shaft?
For model number MGDX655DW0
Hi Dan, thank you for getting in touch. If the shaft came out with the knob, then you may have a broken dryer switch, part number PS8746437. You may need to replace the switch. We hope this solves your problem!
Pryed dryer top open and opened front door. . Unscrewed the 2 retaining screws. Pulled old switch from the wiring harness. Put new switch in place and replaced the retaining screws. Put new switch wire plug into the wiring harness. Before closing top, checked door switch function with dryer on. Dryer cut off when door open and when closed dryer started normally. . . Maint. Note instruction book should warn that letting door slam, which I did on occaision, broke the switch arm. Might save future problems.
It was simple once I figured out what to do:). I removed the 2 screws on the top of the dryer... they were a bit hard to find. Even with the other descriptions on this site. I was removing things I didn't need to. The 2 screws you need to remove are under the LINT COLLECTOR LID. Remove those 2 screws & lift the lid... it will be tight at first. the front of the lid has 2 "catches" in the corners.
The hardest part was getting the door switch assembly to "unplug". We pried it off -- eventually -- & then simply plugged in the new one.
Saved me LOTS of money & was worth the 30 minutes - 1 hour of work.
As I said previously, once you realize how to get the lid up & manage to pry off the plug, that's all there is to it -- easy!
