This kit includes one bearing, one ball shaft, one ball bearing, one ball bearing retainer, a small tube of high temperature lubricant, and installation screws.
$57.02
In Stock
Order within the next 11 hrs and your part ships today!
The rear drum support bearing helps support the dryer drum to rotate quietly and smoothly during operation. The bearing attaches on the inside of the rear panel of the dryer cabinet. If your dryer is ...
$12.62
In Stock
Order within the next 11 hrs and your part ships today!
This thermal fuse limiter, with a limit of 220 degrees Fahrenheit, is manufactured for both gas and electric clothes dryers. Once the internal temperature of the dryer reaches 220 degrees, the heating element cuts out.
$15.17
In Stock
Order within the next 11 hrs and your part ships today!
This dryer lint screen is for laundry centers.
Dryer lint screen captures lint and debris from the exhaust air flowing from the dryer.
Follow the instructions in the owner's manual when installing this part.
$54.49
In Stock
Order within the next 11 hrs and your part ships today!
The pump is what your washer uses to remove the water from the tub. This part is the pump and motor assembly which includes the red flapper to prevent drain back flow.
$265.77
In Stock
Order within the next 11 hrs and your part ships today!
Order within the next 11 hrs and your part ships today!
Questions And Answers for MEX731CFS2
Ask our experts a question about this model and we'll get back to you as soon as possible!
5 questions answered by our experts.
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Angela
November 30, 2019
Hi, do you know if this model is electric or gas?
For model number MEX731CFS2
Hi Angela, looks like it can be either. Thank you for your question and good luck with your repair!
1 person found this helpful.
Was this helpful?
Thank you for voting!
Jan
March 12, 2020
When i turn on the dryer it starts but shuts off right away. I have checked the dryer belt and it is fine. What is your suggestion?
For model number MEX731CFS2
Hello Jan, thank you for writing. There are a few parts we advise checking when that issue occurs. Those would be the Door Switch, Thermal Fuse, and Timer. Here is a link to a page where those parts will be listed and it explains how to check them: https://www.partselect.com/Repair/Dryer/Will-Not-Start/ .
1 person found this helpful.
Was this helpful?
Thank you for voting!
Gail
April 27, 2024
The dryer turns on but doesn't heat up
For model number MEX731CFS2
Hello Gail, thank you for getting in touch. Based on our understanding of the issue, we would suggest checking the cycling thermostat, part number PS417453, to solve the problem. It monitors and regulates the temperature inside the dryer. We hope this solves your problem!
Hello, I am looking to replace the shaft for the dryer knob. It's the shaft that turns on the dryer, NOT the one to select dryer cycle.
Make: Electrolux
Model: MEX731CFS2
Serial: XE90300667
Thanks!
For model number MEX731CFS2
Hi Moses,
Thank you for your question. The shaft is part of the start switch. The part number listed under your model number for the start switch is PS1146154. If you need help placing an order for it, customer service is open 7 days a week and anyone will be happy to assist you. Please feel free to give us a call. We look forward to hearing from you!
The knob of my dryer is not working, found the model no in dryer: Electrolux Home Products MODEL MEX731CFS2 SERIAL XE91802193. Is it available?
For model number MEX731CFS2
Hi Monica, thank you for reaching out. The dryer timer knob for your model is part number PS418891, and the control knob for your dryer is part number PS418888. We hope this solves your problem!
1. Unplug dryer from outlet 2. Using Lg. flat screwdriver, pry under the front edge of the top and release two spring tabs 3. Lift up top and tilt back out of your way 4. Unscrew two phillips scews on inside of front panel 5. Lift up and out the front panel. Two spring clips at bottom. 6. Rlease tension on drum belt at the motor. Access panel at rear of dryer. 7.Unscrew 3 screws from inside, center rear of drum. 8. Remove drum through the front of the dryer. You may have to spread the sides apart a little bit for it to fit 9. Lift up on the rear drum bearing to remove it from the bearing retainer. ( U shaped plastic socket) 10. unsrew 2 screws and remove the bearing retainer, ground ball. Ball retainer is on outside of dryer. 11. Vacuum everything--duct, blower, lint trap, ect. 12. Intall new bearing retainer and grounding ball, an assistant is helpful at this time, one to hold ball retainer on rear of dryer, one to screw it in from the inside 13. reassemble remainder of parts in reverse order.
carefully pry up on front washer top to release plastic keeper pins,remove 2 phillips screws from beneath lower front washer panel,slightly lift upward on panel to release.remove old broken belt,push new belt beneath large tub pulley,put belt on small motor pulley,push back belt tension /idler arm,start belt on large tub pulley,turn tub pulley by hand to run belt on,release tension on idler arm.replace front panel and lower top.WALAAH!!!! you are done.
Unplugged Dryer. Opened top of Dryer, over the drum. Removed Thermal Limiter. Tested the Thermal Limiter - found it was open. Checked all vents and exhaust tube for lint build-up. Replaced Thermal Limiter. Closed top of dryer. Plugged Dryer back. Tested Dryer - it works.
