This an authentic OEM 40-Watt replacement light bulb, used in a number of household appliances. It is specially designed to withstand extreme temperatures, which is why these replacement bulbs are mos...
$22.58
In Stock
Order within the next 7 hrs and your part ships today!
The oven sensor detects the temperature within the oven cavity and sends the information to the control board. If your oven is not heating evenly, has little or no heat when baking, or is too hot, you...
$53.22
In Stock
Order within the next 7 hrs and your part ships today!
This is a multi-use and multi-appliance screw. It can be used on a microwave, refrigerator, range/oven, air conditioner, dehumidifier, washer, or dryer. The measurements of this screw are 8 x 1/2 inch...
$26.58
In Stock
Order within the next 7 hrs and your part ships today!
Keep your oven safe and functional with this replacement interior door glass, the heat-resistant panel that lines the inside of your oven door. With dimensions of approximately 20 5/8" x 13 1/8", it f...
$160.20
In Stock
Order within the next 7 hrs and your part ships today!
This is a replacement screw and washer for your oven/range. It is a Phillips-head screw approximately half an inch long, and the washer is approximately 1 inch in diameter. The screw attaches the oven...
$10.09
In Stock
Order within the next 7 hrs and your part ships today!
Order within the next 7 hrs and your part ships today!
Questions And Answers for MER5552BAW
Ask our experts a question about this model and we'll get back to you as soon as possible!
2 questions answered by our experts.
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Laura
December 3, 2019
I need to be able to clean under the drip pans, but there is no wire to hold up the whole stovetop like most models have. The whole stove top is screwed down. I can see that there is a place to put wires on both sides under the stovetop cover--are lift wires available? We have to be able to clean this every week and having to unscrew them every time is not efficient nor practical. We did not notice this unfortunate glitch when we bought it.
For model number MER5552BAW
Hello Laura and thanks for writing.
They are not available to retrofit on this model, however, there might be a crossover from other models. For more specialized assistance or to speak with someone about this, we would suggest calling the manufacturer of the unit directly. Once you get the information you need, we should be able to find the information on our site for you. Hope this helps Maytag 800-344-1274
Was this helpful?
Thank you for voting!
Susan
November 21, 2025
We bought an older maytag stove top stove but burners do not work. Is it possible to buy some for this model numbr and how much? Thanks
For model number MER5552BAW
Hi Susan, thank you for reaching out. The 6-inch surface burner elements for your model are part number PS11751368, and the 8-inch surface burner elements are part number PS11753288. They are sold individually. We hope that helps!
Removed the oven door by opening slightly, then pic door up to remove. Remove 2 screws holding oven sensor in place, gently pull on sensor to remove, had to remove about 8 inches to get at plastic connector. Unplug connector, had to use an adapter cable supplied with the PartSelect kit to install new sensor, push cable back into opening, reinstall 2 screws. The oven works fine! Note that due to thermal lag the temperature overshoots to 370 degrees and undershoots to 340 degrees, this appears to be normal oven operation. Putting door back in place was easy.
I ordered gray enamel drip bowls and they fit perfectly. Unfortunately 2 of them were chipped and bent slightly. They still worked which was better than the make shift ill fitting ones that came with the house so I decided to keep them. I did tell parts select about it and they sent me a new order of drip pans at no charge. I used the perfect ones but the 8" drip pans flaked off paint after one use. I guess this is an Amana defect...the paint doesn't stick under heat.
Moved the Appliance out unplugged it and removed the backing plate then Remove the Knob and unscrew the infinite switch then marking the 5 wires to know where the go on the new switch, removing and replaced it with the new one
.gif "SUPPLEMENTAL INFORMATION Diagram and Parts List for Maytag Range")
