This drum support roller is sold individually. Most dryers require two. The tri-rings are included. This is a drum support roller for a dryer. It is a genuine replacement part. This part is sold separ...
The drum support roller kit (Dryer Repair Kit) allows the dryer to tumble properly by supporting the drum cylinder. The idler pulley provides the tension required for a multi-ribbed belt. The belt att...
This thermal cut-off kit for a dryer includes one high limit thermostat with a limit of 250 degrees Fahrenheit, and one thermal cut-off fuse (309 degrees). This kit also includes flat heaters with jumper wires.
If you notice that your dryer is noisy or will not tumble, you may need to replace the tri ring. This part is triangular, and is less than an inch in size. Tri rings can be found both on the idler pul...
This 18 ml bottle of white appliance touch-up paint is used to cover scratches or marks on your appliance. The white touch-up paint can be used on refrigerators, microwaves, ranges, clothes dryers, an...
This high-limit thermostat with Terminal Extension Arm acts as as safety mechanism that keeps the dryer from overheating. Once the dryer temperature reaches 221 degrees Fahrenheit, this piece will shu...
If your dryer drum isn’t spinning, the motor might be the issue. This replacement motor works with many Whirlpool-brand dryers made before 1996 and comes with the pulley already attached. It powers th...
Brighten up your appliance with this easy-to-install 10-watt light bulb, perfect for dryers and refrigerators. It gives off a clear, steady light so you can easily see inside when the door is open. Wh...
The blower wheel is a squirrel cage type wheel whose purpose is to move the air through the room or appliance. The blower wheel spins on the motor shaft to blow air through the dryer drum and out through the exhaust.
$46.44
In Stock
Questions And Answers for MEDX655DW0
Ask our experts a question about this model and we'll get back to you as soon as possible!
5 questions answered by our experts.
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Cynthia
September 5, 2023
Looking for dryer fan?
Dryer heats but does not dry
For model number MEDX655DW0
Hi Cynthia, thank you for reaching out. The part you are looking for is the blower wheel, part number PS11743785. We hope this information helps!
The lint vent on the right top of dryer broke when I tried to clean it; need part that attaches to it. lint screen
For model number MEDX655DW0
Hi Helen, thank you for reaching out. The lint filter you are looking for is part number PS16744837. If you need help placing an order, customer service is open 7 days a week!
Dryer will not start if put in sensor dry but works in timed dry
For model number MEDX655DW0
Hello Mike, thank you for your question. The part you will need to replace is the Timer PS11756913. Here is a testimonial from a previous customer on how to install. Repair was fairly simple, unplug power from dryer, take back top panel off, remove timer knob, remover timer switch, un-plug one lead at a time, and place on new timer, reconnect timer, put back on back panel, reconnect power to dryer. Good luck with your repair.
why or what is the reason for the black wire melting the terminal block
For model number MEDX655DW0
Hello Bryan, thank you for writing. A burned through wire on the terminal block is usually caused by a poor electrical connection. The poor connection causes a higher amp draw through that wire which eventually gets hot enough to melt through the wire and terminal block. We hope this helps.
Was this helpful?
Thank you for voting!
Stephanie
February 14, 2025
I need to figure out where the heating element is on my dryer
For model number MEDX655DW0
Hello Stephanie, thank you for your question. The Heating Element is PS11723099. We hope this helps.
First tried heating element and thermal fuse with no luck. Ordered thermal cutoff and fixed problem. Had I used an ohm meter first I would have determined problem before having ordered heating element and fuse, as both had resistance. I wast just lazy and ordered the took the most common failed components first before taking dryer back off.
Pryed dryer top open and opened front door. . Unscrewed the 2 retaining screws. Pulled old switch from the wiring harness. Put new switch in place and replaced the retaining screws. Put new switch wire plug into the wiring harness. Before closing top, checked door switch function with dryer on. Dryer cut off when door open and when closed dryer started normally. . . Maint. Note instruction book should warn that letting door slam, which I did on occaision, broke the switch arm. Might save future problems.
